Related Manuals for Gearmore 2G2 Series
Summary of Contents for Gearmore 2G2 Series
- Page 1 INDUSTRIAL SCRAPER Operation, Service & Parts Manual For 2G2 Series October 2001 Form: 2G2Book.pm65\10-01...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Preparation ..............1 Safety Information ............2 General Information ............. 3 Maintenance/Safety ............4 Assembly Instructions ..........5 Parts Breakdown ............6-10 S2x4-9G2 Cylinder ............11 Limited Warranty ............12 DATE OF PURCHASE: _______________________ MODEL NUMBER: ___________________________ SERIAL NUMBER: ___________________________... -
Page 3: Preparation
PREPARATION/TRAINING WARNING: To prevent possible personal injury or death during assembly, installation, operation, adjustment or removal of implement; DO NOT wear loose clothing, always wear gloves and safety glasses or face shield. Keep other persons away from any unit under power. READ BEFORE OPERATING BOX SCRAPER TRAINING: Know your controls. -
Page 4: Safety Information
SAFETY INFORMATION OPERATIONAL SAFETY: Read and observe all safety decals on Stop tractor immediately upon strik- the tractor and scraper. ing an obstruction. Turn off engine, inspect and repair any damage before DO NOT stop or start suddenly when resuming operation. -
Page 5: General Information
GENERAL INFORMATION - are reversible so CUTTING EDGES REPLACEABLE SHANK POINT always remember to "fl ip" them over make sure you replace the point before before wearing the back plate. Replace the you wear the drop forged shank. Knock cutting edge after both edges are worn to off the worn point and lock the new point the bottom edge of the back plate. -
Page 6: Maintenance/Safety
MAINTENANCE SAFETY Lower box scraper to ground, set Periodically tighten all bolts and nuts tractor locking system device, turn to ensure scraper is in a safe working tractor engine off, and remove key condition. before performing any service or maintenance. -
Page 7: Assembly Instructions
ASSEMBLY INSTRUCTIONS 1. Attach box scraper to 3-point hitch 6. Crack fi tting on cylinder and cycle in lower lift arms using pins supplied. order to remove air from the system. 2. Attach 3-point hitch top link to 7. Raise scraper off the ground with A-frame mast on scraper using pin tractor 3-point hitch. -
Page 8: Parts Breakdown
REPLACEMENT PARTS... - Page 9 REPLACEMENT PARTS REF # PART NO. DESCRIPTION 60" 66" 72" 76" P075500C1TL Cat. 1 Top Link Pin X01A31P Top Link Pin Stop P716175LY Lynch Pin R04AB001 Top Cylinder Rod SS516075 Set Screw SC075050SSC Cylinder Rod Lock Collar " P050175CL Link Pin "...
- Page 10 WELDMENT REPLACEMENT PARTS...
- Page 11 WELDMENT REPLACEMENT PARTS REF # PART NO. DESCRIPTION 60" 66" 72" 76" P03A05 Top Link Ear P03A05A Top Link Ear With Pin Stop P02A100 Top Cylinder Ear T04A3A Mast Spacer Assembly (Includes mast spacer, cylinder ear and both top link ears) P03A011 Mast P03A011A...
- Page 12 WELDMENT REPLACEMENT PARTS REF # PART NO. DESCRIPTION 60" 66" 72" 76" P00A229A Back Plate Assy w/Bridge (no cutting edge) P00A329A Back Plate Assy w/Bridge (no cutting edge) P00A429A Back Plate Assy w/Bridge (no cutting edge) A09A124A Back Plate Bridge Assy (Includes bridge and bridge gussets) A09A224A...
-
Page 13: S2X4-9G2 Cylinder
S2X4-9G2 CYLINDER REF # PART NO. DESCRIPTION QTY. IT2N Crimped Locknut LC2V Piston Crown Seal O-Ring IT2C Barrel Rod Seal O-Ring Back-up Ring IT2E-S-1.2 Gland Wiper Seal IT2S Piston Rod * Parts available Packing Kit in packing kit SK24-6 ( Consists of: 1 ea. only Ref.# 3, 4, 6, 7, 8, &... -
Page 14: Limited Warranty
Our obligation shall be limited to repairing or replacement of any part, provided that such part is returned within thirty (30) days from date of failure to Gearmore through the dealer from whom the purchase was made, transportation charges prepaid.