Advertisement
Quick Links
Kit Number 626AK010 or 771AK010
This instruction sheet describes how to install the monitor mount kit (626AK010) for Cybex Arc model
62X or monitor mount with Netpulse cables kit (771AK010) for Cybex Arc model 77X.
Tools Required
Phillips screwdriver
•
1/2" Wrench
•
5/16" Wrench
•
7/16" Wrench
•
5/16" Allen wrench
•
5/32" Allen wrench
•
Side cutters
•
Block
•
Read and understand all instructions thoroughly before installing this kit.
Verify the kit contents shown.
1
2
3
4
5
6
12
13
14
15
16
Monitor Mount Kit
7
Page 1 of 9
Installation Instructions
Description
1
Back cover
2
5/16" Locknut
3
Washer
11
4
Bolt
5
1" Screw (6)
6
1/4" Locknut (6)
7
1/2" Screw (2)
10
8
Hood
9
Decal
9
10 Vesa mount
11 Support tube
8
12 Cable tie
13 Connector
(771AK010 only)
14 CSAFE cable
(771AK010 only)
15 CAT6 cable
(771AK010 only)
16 Power and COAX cable
(771AK010 only)
N/A 626AK010 cables not
supplied
www.cybexintl.com
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for CYBEX 771AK010
Summary of Contents for CYBEX 771AK010
- Page 1 Monitor Mount Kit Installation Instructions Kit Number 626AK010 or 771AK010 This instruction sheet describes how to install the monitor mount kit (626AK010) for Cybex Arc model 62X or monitor mount with Netpulse cables kit (771AK010) for Cybex Arc model 77X. Tools Required Phillips screwdriver •...
- Page 2 Disconnect external power source Unplug power cord from the power outlet. WARNING: Shock and electrocution hazard Unplug unit and let sit 10 minutes before cleaning or performing maintenance • Electrical charge can remain in unit after unplugging • Keep water and liquids away from electrical parts •...
- Page 3 Remove console assembly 1. Remove the six screws securing the console assembly to the console support using a Phillips screwdriver. Description Console assembly Console support Screw (6) 2. Disconnect display cables and pull up through weldment. 3. Set console assembly aside for reinstallation. Page 3 of 9 www.cybexintl.com...
- Page 4 Remove console support Remove and discard the six screws securing the console support to the weldment using a Phillips screwdriver and a 7/16” wrench. Description Console support Weldment Screw (6) Install tube support 1. Install the six 1” screws and 1/4” locknuts securing the weldment to the console support and the support tube using a Phillips screwdriver and a 7/16”...
- Page 5 2. Install the two 1/2” screws securing the hood to the support tube using a Phillips screwdriver. Place decal on top of hood. Description Support tube Hood 1/2” Screw (2) 3. Install the bolt, washer, and 5/16” locknut securing the vesa mount to the support tube using a 5/16”...
- Page 6 Route cables (771AK010 shown - 626AK010 cables not supplied) 1. Route the power and COAX and the CAT6 cables through the top of the support tube and down into the weldment. Description Support tube Weldment Power and COAX CAT6 CSAFE 2.
- Page 7 Remove right wheel 1. Place a block under unit to elevate right wheel. Block must be at least 3.5” high. Bolt Minimum 3.5” High Wheel Lockwasher Block 2. Remove bolt, lockwasher, and nut securing right wheel using a 7/16” wrench and a 5/32” Allen wrench.
- Page 8 Install console assembly 1. Plug CSAFE cable into the MCC board on the console assembly. Description CSAFE cable 2. Install the six screws securing the console assembly to the console support using a Phillips screwdriver. Description Console Assembly Console Support Screw (6) Page 8 of 9 www.cybexintl.com...
-
Page 9: Complete Installation
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. 10 Trotter Drive Medway, MA 02053 508-533-4300 • FAX 508-533-5183 • www.cybexintl.com Copyright © 2013, Cybex International, Inc. All rights reserved • 771A-327 • October 2013 Page 9 of 9 www.cybexintl.com...
Need help?
Do you have a question about the 771AK010 and is the answer not in the manual?
Questions and answers