Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Daesung Celtic SHW-16
Summary of Contents for Daesung Celtic SHW-16
- Page 1 SHW,HW-13~24 FF...
- Page 4 Banit...
- Page 7 4500 Banit...
- Page 8 (SHW-13~24)
- Page 9 (HW-13~24) In use Error Power Low Temp High Temp Control...
- Page 10 SHW 13~24 40℃...
- Page 11 HW 13~24 Error Indicator Combustion Indicator Power Indicator Lamp will be on if a Failure occurs In use Error Power Low Temp High Temp Control Control...
- Page 13 SHW 13~30 40℃) 37℃~45 ℃, 47℃, 48℃, 50℃, 55 ℃, ℃, 65℃ 70℃) 37℃~45 ℃( in 1 ℃ increments) 50℃~70℃ , 45℃ 50℃ 50℃...
- Page 14 HW 13~24 Press the power On/Off button. In use Error Power Low Temp High Temp Control Set temperature by using the controller. In use Error Power Low Temp High Temp Control Turn on hot water.
- Page 17 1.3Liters...
- Page 18 2.6 LPM (p.17) 220V 50Hz. 2.6LPM (p.17)
- Page 19 2.6 LPM. (p.17) (p.17)
- Page 20 10kg/cm...
- Page 22 Daesung Celtic...
- Page 23 SHW-13 SHW-20 SHW-24 SHW-16 Wide Deep (mm) High Gas control method Modulating PT 1/2"(15A) PT 3/4"(20A) PT 1/2"(15A) PT 1/2"(15A) 1,830 2,250 2,710 3,080 (gr/h) Efficiency 94.6 95.4 95.9 94.4 Minimum Operation Pressure (bar) Normal Operation Pressure (bar) 230V / 50Hz Concentric (Air Intake : Φ100, Flue Outlet : Φ60)
- Page 24 HW-13 HW-16 HW-20 HW-24 Wide Deep (mm) High Gas control method Modulating PT 1/2"(15A) PT 3/4"(20A) PT 1/2"(15A) PT 1/2"(15A) 1,830 2,250 2,710 3,080 (gr/h) Efficiency 94.6 95.4 95.9 94.4 Minimum Operation Pressure (bar) Normal Operation Pressure (bar) 230V / 50Hz Concentric (Air Intake : Φ100, Flue Outlet : Φ60) (mm) △T 25℃...
- Page 25 Isometric View SHW-13~24...
- Page 28 PCB Box 3040256 3084029 13+21 Pin wire 3130371 M4 X 12 Screw 3100108 3100108 Hood assembly(SHW-13) 2070488 2010338 2070489 Hood assembly(SHW-16~24) (SHW-13) 2010339 3010876 Flue guide (SHW-13) (SHW-16~24) Flue guide(SHW-16~24) 3011135 2070405 Latent heat exchanger assembly Burner Assembly(SHW-13) 2020299 (SHW-13)
- Page 29 2090863 Cold water inlet pipe(SHW-13) 2090899 Cold water inlet pipe (SHW-16~24)
- Page 30 Isometric View HW Model(13~24)
- Page 33 2080364 13+21 Pin wire 3130393 3084029 M4 X 12 Screw 3100108 3100108 Remote controller 2080576 2070488 Hood assembly(HW-13) 2010314 Hood assembly(SHW-16~24) 2070489 (HW-13) 2010358 3010876 Flue guide (HW-13) 3011135 Flue guide(HW-16~24) (HW-16~24) 2070405 Latent heat exchanger assembly Burner Assembly(HW-13) 2020299...
- Page 34 3130380 Cold water inlet temperature sensor 2090880 Cold water inlet pipe(HW-13) 2090881 Cold water inlet pipe (HW-16~24)
- Page 37 220V AC - 50Hz. Daesung Celtic Daesung Celtic or Banit Daesung Celtic system.
- Page 38 7℃.
- Page 39 National regulations...
- Page 40 30cm [cm] 20cm 20cm 60cm 20cm 60cm 30cm 60cm 30cm 30cm...
- Page 42 30cm...
- Page 43 Flue piping of concentric type boiler Warning Minimum Please install an exhaust pipe over 10 degree upward in order to protect the boiler from condensed water or rain drops from an exhaust pipe. Please check all air or exhaust pipe connection not to have gas leak.
- Page 44 Warning Exhaust pipe should be far more than 30cm from a wall. Ceiling Please remove projections within 1.5m around air, exhaust pipe top. minimum Air, exhaust pipe top should be away from a upper part projection more than 25cm. Please install an exhaust pipe minimum 10˚...
- Page 45 Installation standard or how to install of an air, concentric pipe. Please connect elbow or extension vent as an exhaust pipe is done and make the locked hang on a groove. When use elbow or extension vent, please connect carefully not to tear the connection part.
- Page 46 230V AC, 50Hz.
- Page 47 SHW,HW...
- Page 50 SHW-13~24 Models 108.5 Hot water Hot water outlet connection Gas inlet Connector inlet connection PT 1/2" PT 3/4" PT 1/2" 49.9 83.1 44.9...
- Page 51 HW-13~24 Models In use Error Power Low Temp High Temp Control Gas inlet Connector PT 3/4" Hot water Hot water inlet connection outlet connection PT 1/2" PT 1/2"...
Need help?
Do you have a question about the SHW-16 and is the answer not in the manual?
Questions and answers