Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Paoli Avvitatori STORM A.08.0005
- Page 1 STORM...
- Page 2 Grazie per aver scelto un prodotto PAOLI. Dietro il vostro prodotto ci sono la capacità e l’impegno di un team aziendale che lavora tutti i giorni per essere in grado di offrirvi sempre dei prodotti potenti, affidabili e durevoli nel tempo. Dalle Pit Lanes a ogni tipo di attività, il vostro successo è...
-
Page 3: General Power Tool Safety Warnings
General Power Tool Safety Warnings △ ! WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference! The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 4 d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Page 5: Product Safety Instructions
Product Safety Instructions △ ! WARNING 1. To ensure the designed operational integrity of power tools, do not remove installed cover or screws. 2. Use your tool at lower input than specified on the nameplate, otherwise, the finish may be spoiled and working efficiency reduced by motor overload. 3. - Page 6 Additional Safety Rules For Charger & Battery Pack △ ! WARNING 1. Do not charge battery pack when temperature is below 0°C (32°F) or above 40 °C (104°F). 2. Do not attempt to use a set-up transformer, an engine generator or DC power receptacle.
-
Page 7: Specific Safety Rules And/Or Symbols
Specific Safety Rules and/or Symbols --------Recycle ------Class II Tool --------Do Not Throw In Garbage V--------Volts a.c.------Alternating Current Hz-------Hertz W--------Watts - - - - - - o l i mm------Millimeter ----Direct Current r.p.m.----Revolutions or ft-lb-----Foot-Pound Reciprocations Per Minute Specifications Model No. A.08.0005 a t l d.c. - Page 8 View the Major Components Anvil Main Switch Battery Knob Forward/Reverse Rod Belt Battery Pack Fuel Gauge...
-
Page 9: Charging The Battery Pack
Operating Instructions (Slide-In) Installing or Removing Battery Pack 1. Always switch off the machine before insertion or removal of the battery pack. 2. To remove the battery pack, push the button on the battery pack and pull the tool unit from the battery pack in the direction. 3. - Page 10 The LED Light on the Charger Power On (Green light flashes slowly) Battery Low (Red light stays illuminated) Battery charged 80% (Green light flashes rapidly) Battery charged 100% (Green light stays illuminated) Battery Pack temperature is too hot or too cold (Red light flashes slowly) Battery Pack malfunction (Red and Green lights stay illuminated) Battery Pack LED Indication Function The Battery Pack has a “SW”...
- Page 11 Installing or Removing Socket (Impact Wrench) Always be sure that the machine is switched off and the battery pack is removed before installing or removing the socket. Fig.4 Fig.5 Caution 1. To install the socket, push the socket into the driving spindle as far as it will go. (See Fig.4) 2.
- Page 12 When the battery pack is discharged almost completely, voltage will drop and the tightening torque will be reduced. Driver bit or socket bit: Failure to use the correct size driver bit or socket bit will cause a reduction in the tightening torque.
- Page 13 LED illustration After machine is activated; LED will be on by release trigger and stay illuminated for 10 seconds then off automatically. Installing Or Removing Hook (optional) Installing Hook： Use Phillips or slotted bit size bit and tighten in clockwise. Removing Hook：...
- Page 14 12-1 12-2 14-1 14-2 13-1 13-2 PARTS NAME PARTS NAME FRONT COVER SCREW 14-2 MAIN SWITCH FRONT COVER ASS'Y 15 LED HOLDER RUBBER WASHER 16 FORWARD/REVERSE ROD WASHER 17 HOUSING LABEL FRONT IMPACT ASS'Y 18 FUEL GAGUE COVER REAR IMPACT ASS'Y 19 SCREW BEARING 20 HOUSING-L&R...
-
Page 15: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY Individual machine DINO PAOLI S.R.L. - Via G. Dorso, 5 - 42124 Reggio Nell’Emilia (Re) - Italy declare under our sole responsibility that the product: Machine Type STORM Cordless impact wrench TECHNICAL DATA View Operating and Maintenance Manual at page 5 SERIAL NO. - Page 16 DINO PAOLI s.r.l. Via G. Dorso, 5 - 42124 Reggio nell’Emilia (RE) - Italy Phone +39 0522 364 511 - Fax +39 0522 304 864 sales@paoli.net - www.paoli.net...