Advertisement
Quick Links
GAS VIC (AUTO-IGNITE)
ASSEMBLY AND MO UNTING INSTRUCTIONS
G E N ER AL NO T E S
•
THIS LUMINAIRE IS SUITED FOR WET LOCATIONS.
•
WHEN INSTALLING LUMINAIRE, CONFORM TO ALL APPLICABLE
LOCAL CODES OR IN THE ABSENCE OF LOCAL CODES, WITH THE
NATIONAL FUEL GAS CODE.
•
FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ
AND UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE
COMMENCING INSTALLATION OF THIS LUMINAIRE.
•
CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
•
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
•
THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED
ELECTRICIAN/GAS PLUMBER. PLEASE WEAR GLOVES TO PROTECT
THE FINISH OF THE FIXTURE.
MAINTENANCE INSTRUCTIONS
•
KEEP APPLIANCE CLEAR AND FREE FROM COMBUSTIBLE
MATERIALS, GASOLINE AND OTHER FLAMMABLE VAPORS AND
LIQUIDS
•
DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION
AIR.
•
VISUALLY CHECK THE BURNER AND PILOT FLAMES WITH PICTORIAL
REPRESENTATIONS.
•
FOR QUESTIONS OR REPLACEMENT PARTS, PLEASE CONTACT
CLIENT SERVICES AT 843.723.8140 OR
INFO@URBANELECTRICCO.COM
W AR NI NG S
FOR APPLIANCES FOR INDOOR INSTALLATION:
INSTALLATION:
DANGER
FIRE OR EXPLOSION HAZARD
IF YOU SMELL GAS:
1. SHUT OFF GAS TO THE APPLIANCE.
2. OPEN WINDOWS.
3. DON'T TOUCH ELECTRICAL
SWITCHES.
4. EXTINGUISH ANY OPEN FLAME.
5. LEAVE THE BUILDING
IMMEDIATELY.
6. AFTER LEAVING THE BUILDING,
IMMEDIATELY CALL YOUR GAS
SUPPLIER OR FIRE DEPARTMENT.
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE
VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER
APPLIANCE.
FOR APPLIANCES FOR OUTDOOR
IF YOU SMELL GAS:
FOR ALL APPLIANCES:
WARNING
FIRE OR EXPLOSION HAZARD
DANGER
FIRE OR EXPLOSION HAZARD
1. SHUT OFF GAS TO APPLIANCE.
2. EXTINGUISH ANY OPEN FLAME.
3. IF ODOR CONTINUES, LEAVE THE
AREA IMMEDIATELY.
4. AFTER LEAVING THE AREA, CALL
YOUR GAS SUPPLIER OR FIRE
DEPARTMENT.
U E - 1 7 4 4
Advertisement
Summary of Contents for Urban Electric GAS VIC
- Page 1 GAS VIC (AUTO-IGNITE) ASSEMBLY AND MO UNTING INSTRUCTIONS U E - 1 7 4 4 G E N ER AL NO T E S • THIS LUMINAIRE IS SUITED FOR WET LOCATIONS. • WHEN INSTALLING LUMINAIRE, CONFORM TO ALL APPLICABLE LOCAL CODES OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE.
- Page 2 GAS VIC (AUTO-IGNITE) ASSEMBLY AND MO UNTING INSTRUCTIONS U E - 1 7 4 4 • FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN FIRE OR EXPLOSION, WHICH COULD CAUSE PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH. CO M PO N ENT S P RO VI DE D FO R I N ST ALL AT IO N...
- Page 3 GAS VIC (AUTO-IGNITE) ASSEMBLY AND MO UNTING INSTRUCTIONS U E - 1 7 4 4 STEP 3 STEP 4 ATTACH THE MOUNTING PLATE TO THE WALL USING THE ATTACH THE FIXTURE TO THE WALL BY SLIPPING THE FOUR MOUNTING SCREWS AND ANCHORS PROVIDED. IT IS FIXTURE OVER THE MOUNTING PLATE AND TIGHTENING THE IMPORTANT TO CHECK LEVEL ON THE MOUNTING PLATE.
- Page 4 GAS VIC (AUTO-IGNITE) ASSEMBLY AND MO UNTING INSTRUCTIONS U E - 1 7 4 4 STEP 7 STEP 8 INSTALL THE SIDE GLASS PANE (002) BY INSERTING THE WITH THE FIXTURE DOOR OPEN, RE-INSTALL THE GLASS BOTTOM EDGE OF THE GLASS PANE INTO THE CHANNEL AT SUPPORT PAN BY SLIPPING THE PAN OVER THE TOP STUDS THE BOTTOM OF THE FIXTURE.
- Page 5 GAS VIC (AUTO-IGNITE) ASSEMBLY AND MO UNTING INSTRUCTIONS U E - 1 7 4 4 STEP 11A STEP 12 ROUTE GAS LINE. APPLY A THIN LAYER OF PIPE DOPE OR SLIP THE BURNER COVER OVER THE BURNER ASSEMBLY. THREAD SEALANT TO THE THREADED FITTINGS. CONNECT THE GAS SUPPLY TO THE LANTERN AND HAND TIGHTEN ALL FITTINGS.