Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for alre JDS-211
- Page 1 Manual for connection and operation of the JDS-211 page 1 of 16 Manual for connection and operation of JDS-211 (item number: G8000409 00) as of version 2.3 Fa. ALRE-IT Regeltechnik GmbH • Richard-Tauber-Damm 10 • D-12277 Berlin • Phone: (030) 39984-0...
-
Page 2: Table Of Contents
6.3. Manual adjustment of the manipulating variable (manual control) ............... 11 7. Serial interface ......................11 8. Error codes........................12 9. Specification ........................13 10. Disposal notes ......................13 Addendum A: PID-control definition ................14 Addendum B: Tips for using the JDS-211 as heating controller .........15... -
Page 3: Safety Regulations
E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 3 of 16 1. Safety regulations This device was designed and tested considering the safety regulations for electronic measuring devices. Faultless operation and reliability in operation of the measuring device can only be assured if the General Safety Measures and the devices specific safety regulations mentioned in this users manual are considered. -
Page 4: Introduction
LED’s “1” and “2”. Furthermore all devices supports a serial interface for communicating with a host computer. When leaving our factory the JDS-211 has been subjected to various inspection tests and is completely cali- brated. Before the JDS-211 can be used, it has to be configured for the customer’s applica- tion. -
Page 5: Connection Data
E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 5 of 16 3.2. Connection data typical limitations between notes terminals min. max. min. max. or corresponding des- Supply voltage 1 and 2 207 V 244 V 253 V ignation on the type... -
Page 6: General Notes To The Operating Of The Menu
E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 6 of 16 4. General notes to the operating of the menu SP/Tn max. Scale By means of button 1 you can go to the next parameter. Xp/Tv Additionally a given changing in the parameter setting can be con- min. -
Page 7: 2-Point-Controller, 3-Point-Controller, 2-Point-Controller With Alarm
E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 7 of 16 5.1.1. 2-point-controller, 3-point-controller, 2-point-controller with alarm This chapter describes device how to configurate the switching function and how to adjust the switching values of the device used as a 2-point-controller or 3-point-controller. This instruction demands that you selected “2P“, “3P“... -
Page 8: Min-/Max-Alarm (Getrennt Oder Gemeinsam)
E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 8 of 16 “2. Err“ Preferred state in case of error ( only at “3P“) possible settings: „On“ output in case of error active (relay on) „Off“ output in case of error inactive (relay off) “AL.Hi“... -
Page 9: Operation
E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 9 of 16 Press now button 4 to exit the offset- and slope-adjustment menu. Example for offset- and slope-adjustment: The device displays the following values (without offset- or slope-adjustment): 2°C at 0°C and 102°C at 100°C... -
Page 10: 2-Point-Controller With Alarm
E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 10 of 16 “1.CyC“ cyclic time in sec possible settings:: 0,1 ...320,0. “2.0n“ turn-on-point of switching function 2 ( only at “3P“) possible settings:: min..max. display range “2.0ff“... -
Page 11: Manual Adjustment Of The Manipulating Variable (Manual Control)
With the help of a software (like EbxKonfig – freeware version available via internet at alre.de) you are able to reassign an address to the device. Additional accessories needed for the interface mode: - Level converter: interface of device "... -
Page 12: Error Codes
E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 12 of 16 8. Error codes When detecting an operating state which is not permissible, the device will display an error code The following error codes are defined: Err.1: Exceeding of the measuring range Indicates that the valid measuring range of the device has been exceeded. -
Page 13: Specification
E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 13 of 16 9. Specification Absolute maximum ratings: see chapter 3.2. (Connection data) Measuring inputs: PT100, 3-wire Measuring range: -50.0 ... + 200.0°C Resolution: 0.1°C Accuracy: < 0.3% FS ±1Digit... -
Page 14: Addendum A: Pid-Control Definition
E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 14 of 16 Addendum A: PID-control definition Set point value: The temperature on which the controlling shall be done. Manipulating variable: The power the controller passes on the process. 0 = 0% power; 1 = 100% power. -
Page 15: Addendum B: Tips For Using The Jds-211 As Heating Controller
Manual for connection and operation of the JDS-211 page 15 of 16 Addendum B: Tips for using the JDS-211 as heating controller 1. Set point value „1.SP“ The temperature on which the controlling shall be done. Please set here the desired temperature. - Page 16 E32.0.A3.6C-01 Manual for connection and operation of the JDS-211 page 16 of 16 Tips for identification of the integral time „1.Int“ Please set the following values by the configuration of your device: Set point value “1.SP“: desired temperature Proportional band “1.Pb“: value identified in chapter A.2...
Need help?
Do you have a question about the JDS-211 and is the answer not in the manual?
Questions and answers