Philips VR388/55 User Manual page 11

S
ETTING
When the auto programming is
completed
The following message appears on the
TV, and the lowest channel will be
tuned in.
AUTO CH.SET COMPLETED
Now you have finished the initial set up
procedure.
If you stop the initial setup procedure while
it is proceeding:
The VCR enters the initial setup mode again
the next time your turn on the VCR.
Initial setup will not start in the following
cases:
• If there is a tape inserted.
• If any one of the initial setup procedures
is finished manually.
To reset the clock manually
You can also reset or correct the clock
manually.
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select "INITIAL
SET UP" then press 3.
The Initial Set Up menu appears.
4 Press 5 or ∞ to select "SET
CLOCK" then press 3/OK.
5 Press 5 or ∞ to set the time, then
press 3/OK.
• Each time you press 5 or ∞, the set
time changes by 1-minute intervals. If
you hold the button, the set time
changes by 30-minute intervals.
6 Press 5 or ∞ to set the month and
day, then press 3/OK.
• Each time you press 5 or ∞, the set
date changes by 1-day intervals. If you
hold the button, the set date changes by
15-day intervals.
7 Press 5 or ∞ to set the year, then
press 3/OK.
• Each time you press 5 or ∞, the set
date changes by 1-year intervals. If you
hold the button, the set year changes
rapidly.
8 Press EXIT/STATUS to exit from
the menu operations.
Note:
If a power failure occurs, clock will lose its
setting.
VR388/588-55 EN (N)
U
P
(C )
ONTINUED
To change the language
manually
You can also change the language
manually.
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select "INITIAL
SET UP" then press 3.
The Initial Set Up menu appears.
4 Press 5 or ∞ to select
"LANGUAGE."
5 Press 3/OK to select the language
on the TV screen.
Each time you press the button, the
language changes as follows:
= =
English
6 Press EXIT/STATUS to exit from the
menu operations.
If you want to delete
unwanted channels
You can delete channels manually.
After you have deleted the channels,
they will be not selected by pressing
CH 5/∞.
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select "TUNER SET
UP" then press 3/OK.
4 Press 5 or ∞ to
select "CHANG-
ING TUNER SET
UP" then press
3/OK.
The programmed
channel information list appears with
the settings of the tuned channel
flashing. (You can also watch the
picture of the tuned channel since the
list and the picture alternates on the
TV.)
5 Press 5 or ∞ until an unwanted
channel setting flashes.
6 Press CLEAR to delete the unwanted
channel.
• If you have accidentally deleted a
channel, press 2.
7 Repeat steps 5 and 6 until you delete
all unwanted channels.
8 Press EXIT/STATUS to exit from the
menu operations.
— 12 —
12
If you want to exchange the
channel positions
You can also replace the channel
position numbers.
EX. Replace channel 9 and channel 3
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select "TUNER SET
UP" then press 3/OK.
4 Press 5 or ∞ to select "CHANGING
TUNER SET UP" then press 3/OK.
5 Press 5 or ∞ until information for
channel 3 flashes.
6 Press 3/OK once.
Only channel indication for channel
=
3 starts flashing.
7 Press 0 then 9.
The channel settings for channel 3
and 9 are exchanged.
• If you have accidentally deleted a
channel, press 2.
8 Press 3/OK to store the setting.
9 Press EXIT/STATUS to exit from the
menu operations.
If the picture is not clear
You need to fine-tune this particular
channel.
EX. Fine-tune channel 3
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select "TUNER SET
CH FRQ SYS CH FRQ SYS
01 150 BG 07 229 BG
UP" then press 3/OK.
02 165 BG 08 237 BG
03 195 BG 09 355 BG
4 Press 5 or ∞ to select "CHANGING
04 205 BG 10 365 BG
05 213 BG 11 374 BG
06 221 BG 12 384 BG
TUNER SET UP" then press 3/OK.
5∞
SELECT= DELETE=CLEAR
3
TO CHANGE CH PUSH /OK
5 Press 5 or ∞ until information for
TO END PUSH EXIT
channel 3 flashes.
6 Press 3/OK twice.
Only frequency indication for
channel 3 starts flashing.
7 Press 5 or ∞ to fine-tune the station
until you get the best possible
picture.
8 Press 3/OK to store the setting.
9 Press EXIT/STATUS to exit from the
menu operations.
6/1/99, 9:02 AM