Subscribe to Our Youtube Channel
Related Manuals for Stratasys Finishing Touch
Summary of Contents for Stratasys Finishing Touch
- Page 1 | c-support@stratasys.com Finishing Touch™ Smoothing Station Site Preparation and Installation Guide September 2012 Part No. 108911-0001 Rev. B...
- Page 2 Liability Statement The information in this document is subject to change without notice. Stratasys, Inc. makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Stratasys, Inc. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
- Page 3 The following basic safety tips are given to ensure safe installation, operation, and maintenance of Stratasys equipment and are not to be considered as comprehensive on matters of safety. The Finishing Touch Smoothing Station is designed to be safe and reliable rapid prototyping system. Access to areas of the system are potentially dangerous.
-
Page 4: Table Of Contents
Table of Contents About the Finishing Touch Smoothing Station _____________________________ 1 Welcome to the Stratasys Finishing Touch Smoothing Station___________ 1 Finishing Touch Smoothing Station Components_______________________ 1 Accessory Kit Contents ______________________________________________ 1 Introduction ____________________________________________________________ 2 How To Use This Guide _______________________________________________ 2... -
Page 5: About The Finishing Touch Smoothing Station
About the Finishing Touch Smoothing Station Welcome to the Stratasys Finishing Touch Smoothing Station The Stratasys Finishing Touch Smoothing Station is a method to reduce and in many cases eliminate the need for manual post finishing. Finishing Touch Smoothing Station Components The following items are included in the shipping crate: •... -
Page 6: Introduction
Site Prep Tasks Selecting the Site Decide where to install the system based on the following: Space Requirements • Environmental Requirements • Finishing Touch Smoothing Station Site Preparation and Installation Guide... -
Page 7: Dimensions, Weights And Shipping Temperature
Operating Environment The smoothing station is for indoor use at temperatures from 60°F (15.6°C) to 85°F (26.7°C) Humidity: <65% non-condensing Finishing Touch Smoothing Station Site Preparation and Installation Guide... -
Page 8: Space Requirements
Smoothing Station Figure 1: System Space Requirements Environmental Requirements • The smoothing station is intended for indoor use only. • Operating temperature: 60°F (15.6°C) to 85°F (26.7°C) • Humidity: <65% non-condensing Finishing Touch Smoothing Station Site Preparation and Installation Guide... -
Page 9: Electrical Requirements
The system is equipped with a threaded female fitting (dimensional ¼ NPT standard) for a compressed air connection. The user must supply the necessary connections between the fitting and the customer’s compressed air supply. Finishing Touch Smoothing Station Site Preparation and Installation Guide... -
Page 10: Exhaust Vent Requirements
Do not exceed more than 270° worth of bends. 50 ft. (15.24 m) Flexible Exhaust Hose Outside Exhaust Vent Figure 2: Flexible Exhaust Hose Finishing Touch Smoothing Station Site Preparation and Installation Guide... -
Page 11: Consumables
B-1804 Cargovil (Zemst) Belgium Phone: 00 +32 2 251 95 05 techsupport@microcare.com Randall Oliveiro, Marketing Director Uniwes Technology (S) Pte Ltd 102E Pasir Panjang Road #03-01/02 Citilink Warehouse Complex Singapore, 118529 randall_oliveiro@uniwes.com.sg Phone: 011-65-6275-8183 Finishing Touch Smoothing Station Site Preparation and Installation Guide... -
Page 12: Installing The System
Inspect Crate for Damage Before opening the shipping crate, inspect the crate for signs of exterior damage. Report evidence of excessive damage to Stratasys and the shipping company. Required Tools and Equipment • Basic hand tools (powered screwdriver or drill with phillips bit). -
Page 13: Unpacking The System
Caution: Use care when removing the plastic wrap to avoid scratching the system surfaces. Inspect the system exterior for dents and scratches. Immediately report any damage to Stratasys and the shipping company. Finishing Touch Smoothing Station Site Preparation and Installation Guide... -
Page 14: System Connections
Connect one end of the flexible 4-inch (10.16 cm) exhaust hose to the exhaust port on the back of the system. Connect the other end of the hose to the outside exhaust vent. Finishing Touch Smoothing Station Site Preparation and Installation Guide... - Page 15 Make sure the hose is touching the bottom of the container. Connect the power cord to the electrical supply. Refer to the Finishing Touch Smoothing Station User Guide CD located in the accessory kit for instructions on how to smooth models.
- Page 16 Finishing Touch Smoothing Station Site Preparation and Installation Guide...
Need help?
Do you have a question about the Finishing Touch and is the answer not in the manual?
Questions and answers