1. Manuals
  2. Brands
  3. Cervis Manuals
  4. Extender
  5. SmaRT Link Booster
  6. User manual

Cervis SmaRT Link Booster User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
™
™
Link Booster
User Manual
U090.0.0
©2020 Cervis, Inc.

Advertisement

Table of Contents
loading

Summary of Contents for Cervis SmaRT Link Booster

  • Page 1 ™ ™ Link Booster User Manual U090.0.0 ©2020 Cervis, Inc.
  • Page 2 SmaRT Link Booster This document is the property of Cervis, Inc. and cannot be copied, modified, e-mailed, or reproduced without the express prior written consent of Cervis, Inc. Cervis, Inc. reserves the right to change this manual or edit, delete, or modify any information without prior notification.

  • Page 3: Table Of Contents

    6.0 SmaRT Link Booster Specifications ................11 List of Figures Figure 1. SmaRT Communications Link Booster ............... 1 Figure 2. SmaRT Link Booster Tripod Bracket ................2 Figure 3. Installing the SLB Batteries ..................3 Figure 4. Choosing a Battery ......................4 Figure 5.

  • Page 4: Cervis, Inc. Safety Precautions

    SmaRT Link Booster Cervis, Inc. Safety Precautions ✓ Read and follow all instructions. ✓ Failure to abide by Safety Precautions may cause equipment failure, loss of authority to operate the equipment, and personal injury. ✓ Use and maintain proper wiring. Follow equipment manufacturer instructions.

  • Page 5: Smart Link Booster (Slb) Introduction

    User Manual 1.0 SmaRT Link Booster (SLB) Introduction The SmaRT Link Booster (SLB) is a 900 MHz @ 10 mW or 2.4 GHz @ 100 mW line-of-sight communications booster designed to extend the communication range between a 900 MHz SmaRT remote control unit and a 900 MHz SmaRT base unit or a 2.4 GHz SmaRT remote control unit and a 2.4 GHz SmaRT base unit.

  • Page 6: Figure 2. Smart Link Booster Tripod Bracket

    Operates at 2 V to 4.5 V Eight-character LED display • • 900 MHz @ 10mW broadcast 2.4 GHz @ 100 mW broadcast • • Health LED Battery life (%) menu page Figure 2. SmaRT Link Booster Tripod Bracket U090.0.0...

  • Page 7: Installing "C" Cell Batteries

    Li-ion Battery Pack Insert Figure 3. Installing the SLB Batteries Observe proper polarity when placing batteries into the Caution! cradle. Improper battery placement can cause excessive heat, battery explosion, operator injury, and damage to the unit. ©2020 Cervis, Inc.

  • Page 8: Choosing The Battery

    SmaRT Link Booster 3.0 Choosing the Battery You must select an initial battery, due to the voltage differences between standard single-use and rechargeable batteries. Make this selection whenever you change to a different style battery – alkaline to Lithium Ion, or Lithium Ion to alkaline. Follow these steps to choose which battery is used.

  • Page 9: Slb Indicators

    2. Cycle through the menu pages using the UP or DOWN buttons until the battery status page displays, as illustrated in Figure 6. 3. Exit the menu system by simultaneously pressing the UP and DOWN buttons when satisfied. Figure 6. Battery Status ©2020 Cervis, Inc.

  • Page 10: Handheld And Base Unit Signal Strength Indications

    SmaRT Link Booster  Note: Observe all state, federal, and local disposal laws when disposing of used batteries. 4.2 Handheld and Base Unit Signal Strength Indications While under normal operation, you can see handheld and base unit received signal strength indication (RSSI) values using the Menu system.

  • Page 11: Figure 8. Slb Handheld Serial Number

    User Manual Figure 8. SLB Handheld Serial Number ©2020 Cervis, Inc.

  • Page 12: Using The Slb

    SmaRT Link Booster 5.0 Using the SLB 5.1 SLB Power On Turn on the SLB by pressing the green power button located on top of the unit, next to the battery tube cover. To conserve power, the unit shuts off the display when it is not in either scan mode or menu mode.
  • Page 13 If the SLB found an acceptable base unit ID, the SLB Handheld TX/RX and Base Unit TX/RX LEDs flash, indicating communications. If the SLB did not find an acceptable base unit ID, the SLB Handheld and Base Unit LEDs remain unlit – unless a previously established existing pair is on. ©2020 Cervis, Inc.

  • Page 14: Figure 11. Using Scan To Establish The Link

    SmaRT Link Booster Step 3 Step 2 Step 4 Figure 11. Using Scan to Establish the Link U090.0.0...

  • Page 15: Smart Link Booster Specifications

    User Manual 6.0 SmaRT Link Booster Specifications Table 1. SmaRT Link Booster Specifications Item Description Power +2 V to +4.5 VDC Two “C” Cells – Single-use (2 V–3.3 V) or Rechargeable (3.3–4.5 Batteries –40° C to 70° C (–40° F to 158° F)
  • Page 16 SmaRT Link Booster www.cervisinc.com Visit our Web site at: ©2020 Cervis, Inc. All rights reserved. Content is subject to change without notice. U090.0.0...

Table of Contents