Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Xtralis ADPRO VM22E
- Page 1 ® ADPRO VM22E Audio Switcher Technical Manual November 2017 Doc. 29541_03...
- Page 3 Total Liability To the fullest extent permitted by law that any limitation or exclusion cannot apply, the total liability of Xtralis in relation to the products is limited to: (i) in the case of services, the cost of having the services supplied again; or (ii) in the case of goods, the lowest cost of replacing the goods, acquiring equivalent goods or having the goods repaired.
- Page 4 Xtralis, the Xtralis logo, The Sooner You Know, VESDA-E, VESDA, ICAM, ECO, OSID, HeiTel, ADPRO, IntrusionTrace, LoiterTrace, ClientTrace, SmokeTrace, XOa, XOh, iTrace, iCommand, iRespond, iCommission, iPIR, and FMST are trademarks and/or registered trademarks of Xtralis and/or its subsidiaries in the United States and/or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks of their respective holder(s).
-
Page 5: Table Of Contents
® ADPRO VM22E Audio Switcher Technical Manual Contents Introduction ............................6 About the VM22E ......................... 6 Requirements ..........................6 Scope ............................6 Specifications ..........................6 Front Panel ........................... 7 Back Panel ........................... 7 Ordering Information ........................7 Hardware Installation ..........................8 Summary ............................ -
Page 6: Introduction
® Technical Manual ADPRO VM22E Audio Switcher Introduction About the VM22E ® The ADPRO VM22E audio switcher allows you to switch the audio output from an ADPRO device to one of 4 selectable audio outputs on the VM22E. You can connect up to 8 VM22E units in cascade, creating up to 32 different output channels. -
Page 7: Front Panel
ADPRO device’s MIO card Audio input from ADPRO device, 3.5 mm jack Audio outputs 1–4 to amplifier, RCA (cinch) Ordering Information Use the following reference numbers to place your order with Xtralis: Item Reference number VM22E unit 49840500 including 4-socket flat cable and mini-jack audio cable... -
Page 8: Hardware Installation
® Technical Manual ADPRO VM22E Audio Switcher Hardware Installation Summary To physically set up a system with one or more VM22E units, perform the following steps: Connect the first VM22E unit to the ADPRO device via the MIO card. Connect the first VM22E unit to the ADPRO device’s audio line out. Connect the VM22E unit(s) to the necessary amplifiers and speakers. -
Page 9: Connection Scheme
® ADPRO VM22E Audio Switcher Technical Manual Connection Scheme For the hardware installation of the VM22E, see the connection scheme below. You can find detailed information further below. Description 12 VDC power supply (1 unit only) Back panel first VM22E module ADPRO device rear panel ADPRO device line out (green 3.5 mm jack) to VM22E audio input (3.5 mm jack). -
Page 10: Connection To The Mio Card
The standard supplied flat cable has 4 connectors; you can order a cable with 8 connectors if necessary. If you use less than 4 or 8 units, Xtralis recommends to use the connectors at the ends of the cable, and leave the connectors in the middle unused. -
Page 11: Output Channel Numbering
® ADPRO VM22E Audio Switcher Technical Manual Output Channel Numbering The table below shows how the audio output numbers (1–32) in the XO client software correspond with the VM22E addresses (rotary switch setting 0–7) and the VM22E audio channel numbers (1–4). Audio channel on VM22E unit VM22E address... -
Page 12: Setup In The Xo Client Software
If yes, you can skip all following steps, and proceed with Activating the VM22E Audio Switcher on page 13. If no, continue with the next step. Download and unzip the MIO card firmware from the Xtralis Security Support site www.xtralissecurity.com. Search for keyword USBIO to find the file; filter on Information Type = Firmware. -
Page 13: Activating The Vm22E Audio Switcher
® ADPRO VM22E Audio Switcher Technical Manual Activating the VM22E Audio Switcher To activate the VM22E audio switcher, proceed as follows: Open the XO client software, and choose System > Connections > I/O. Click Configuration. Under Audio switcher type, click VM22E. Click OK. -
Page 14: Volume Control
® Technical Manual ADPRO VM22E Audio Switcher For software versions XOa 3.01 and above, the following screen appears: By default, the system associates each camera to the audio output with the matching number (camera 1 to output 1, camera 2 to output 2…). For the numbering of the audio outputs, see Output Channel Numbering on page 11. - Page 16 UK and Europe +44 1442 242 330 D-A-CH +49 431 23284 1 The Americas +1 781 740 2223 Middle East +962 6 588 5622 Asia +86 21 5240 0077 Australia and New Zealand +61 3 9936 7000 A Disclaimer about this document, statements about Intellectual Property, Copyrights, and Liability, as well as a General Warning are available in an earlier section of this document.
Need help?
Do you have a question about the ADPRO VM22E and is the answer not in the manual?
Questions and answers