Page 1
JA33-001 Bluetooth Transceiver ® Installation and Operating Manual Rev C Jupiter Avionics Corporation 1959 Kirschner Road Kelowna BC Canada V1Y 4N7 Tel: +1 778 478 2232 Toll-Free: 1 855 478 2232 www.jupiteravionics.com Rev B Page i...
Page 2
All rights reserved Jupiter Avionics Corporation (JAC) permits a single copy of this manual to be printed or downloaded for the express use of an installing agency. Any such electronic or printed copy of this manual must contain the complete text of this copyright notice.
® -enabled device to interact with an RS-232 device connected to the JA33-001. The JA33-001 provides fully isolated audio output to allow a noise free installation. The JA33-001 is set up on a per installation basis using a Configuration Cable and downloading the system configuration settings from a PC into non-volatile control devices.
JA33-001 Bluetooth Transceiver ® Installation and Operating Manual 1.3.2 Outputs Name Type BLUETOOTH STATUS ANNUNCIATOR Discrete signal CONFIG DATA FROM JA33 Data signal MUSIC LEFT Audio signal MUSIC RIGHT Audio signal MODE SELECT OUTPUT Discrete signal RECEIVE OUTPUT Audio signal...
Transmit frequency band 2400 to 2483.5 MHz Radio performance operation Class 3 radio power mode. 1.4.1.4 Bluetooth Performance The JA33-001 is always discoverable by Bluetooth devices when not connected to another Bluetooth ® device. The JA33-001 supports Bluetooth ® A2DP, HFP and SPP profiles.
Introduction This section contains unpacking and inspection procedures, installation information, and post-installation checks. Continued Airworthiness Maintenance of the JA33-001 is on condition only. Scheduled inspection and/or periodic maintenance of this unit is not required. Unpacking and Inspecting Equipment Unpack the equipment carefully. Check for shipping damage and report any problems to the relevant carrier. Confirm that the Authorized Release Certificate or Certificate of Conformance is included.
2.4.3 Mechanical Installation The JA33-001 can be mounted in any attitude and location with adequate space and sufficient clearance for the connector and wiring harness. It requires no direct cooling. 2.4.4 Post Installation Checks 2.4.4.1...
All the JA33-001 internal adjustments are set from the Product Configuration Software ProCS™. Configuration data is sent to the JA33-001 via the front panel connector (♫/io), using the Configuration Cables and a computer running the ProCS™ software. For configuration requirements, see section 2.5.1.
Page 10
JA33-001 Bluetooth Transceiver ® Installation and Operating Manual Fig. 1: MUSIC TRANSMITTER (A2DP SOURCE) Fig. 2: HANDS-FREE + MUSIC RECEIVER (HFP + A2DP) Rev C Page 7...
Page 11
A custom Bluetooth ® device name can be typed in to identify the JA33-001 in the user's cell phone. A slider is used to set the volume (minimum 0 – maximum 10) to suit the user's preference. (Default 9). The Bluetooth ®...
2.6.5 Aircraft Audio Systems List This is a list of Aircraft Audio Systems, and shows the configuration information that will be added to the JA33-001 Settings page. If it is desirable to add other Audio systems, click on the Aircraft Audio Systems List. A new audio system and its (the ‘New Aircraft Audio System' button).
JA33-001. The JA33-001 Bluetooth® Transceiver can be configured at installation or in the field by a dealer or installer, using the Jupiter Avionics Corporation ProCS™ configuration software. At that time, the Bluetooth ®...
Installation and Operating Manual Note: If the Bluetooth ® mode of the JA33-001 is changed at a later date, it may be necessary to un-pair the cellphone and repeat the pairing process to reset to the updated mode of operation. 3.3.1 iPhone Connectivity Configuration The default setting for Call Audio Routing allows the iPhone to select where to route calls;...
JA33-001 Bluetooth ® Transceiver Installation and Operating Manual Appendix A - Installation Drawings Introduction The drawings necessary for installation and troubleshooting of the JA33-001 Bluetooth® Transceiver are in this Appendix, as listed below. Installation Drawings DOCUMENT JA33-001 Connector Map JA33-001 Interconnect...
Page 18
Open-drain output for Bluetooth status indicator lamp. Outputs are Balanced. Connection to airframe ground should not exceed 3 FT (0.9 M). Cable shields at the JA33-001 connector pins should be terminated to airframe ground using a tag ring P/N: MS27741-3 or equivalent. CONNECTOR PIN LEGENDS...
Page 19
MUSIC RIGHT OUTPUT LO 15 PREPARED 05-19-16 CHECKED TITLE Bluetooth Transceiver 05-19-16 APPROVED NCAGE CODE PART NO. SHEET L00N3 JA33-001 DOC NO. CONFIDENTIAL & PROPRIETARY TO JUPITER AVIONICS CORP. JA33-001 Interconnect Rev B.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
Page 20
MIC INPUT LO SPARE 11 PREPARED 05-19-16 CHECKED TITLE Bluetooth Transceiver 05-19-16 APPROVED NCAGE CODE PART NO. SHEET L00N3 JA33-001 DOC NO. CONFIDENTIAL & PROPRIETARY TO JUPITER AVIONICS CORP. JA33-001 Interconnect Rev B.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
Page 21
MUSIC RIGHT OUTPUT LO 15 SPARE 11 PREPARED 05-19-16 CHECKED TITLE Bluetooth Transceiver 05-19-16 APPROVED NCAGE CODE PART NO. SHEET L00N3 JA33-001 DOC NO. CONFIDENTIAL & PROPRIETARY TO JUPITER AVIONICS CORP. JA33-001 Interconnect Rev B.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
Page 22
MUSIC RIGHT OUTPUT LO 15 SPARE 11 PREPARED 05-19-16 CHECKED TITLE Bluetooth Transceiver 05-19-16 APPROVED NCAGE CODE PART NO. SHEET L00N3 JA33-001 DOC NO. CONFIDENTIAL & PROPRIETARY TO JUPITER AVIONICS CORP. JA33-001 Interconnect Rev B.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
Page 23
CONFIG DATA TO JAxx PREPARED 05-19-16 CHECKED TITLE Bluetooth Transceiver 05-19-16 APPROVED NCAGE CODE PART NO. SHEET L00N3 JA33-001 DOC NO. CONFIDENTIAL & PROPRIETARY TO JUPITER AVIONICS CORP. JA33-001 Interconnect Rev B.dwg JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT...
The JA33-001 Installation Manual provides detailed installation instructions and wiring diagrams (Section 2, and Appendices A and B). Power is supplied to the JA33-001 through an existing [ ]-Amp circuit breaker that was previously used by the original audio panel. The net electrical load is unchanged.
Page 27
Refer to the JA33-001 Maintenance Manual. 7. Removal and Replacement Information Refer to Section 2 of this manual - the JA33-001 Installation and Operating Manual. If the unit is removed and reinstalled, a functional check of the equipment should be conducted.