Advertisement
Quick Links
Model/Modelo/Modèle
67114 & 67214
Series/Series/Seria
QUIESSENCE
®
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:
1/8" (3.17 mm)
3/32" (2.38 mm)
For easy installation of your Brizo
you will need:
・To READ ALL the instructions completely before
beginning.
・To READ ALL warnings, care and maintenance
information.
Para instalación fácil de su llave
Brizo
®
usted necesitará:
・LEER TODAS las instrucciones completamente
antes de empezar.
・LEER TODAS los avisos, cuidados, e
información de mantenimiento.
Pour installer votre robinet Brizo
facilement, vous devez:
・LIRE TOUTES les instructions avant de débuter.
・LIRE TOUE LES les avertissements ainsi que
toutes les instructions de nettoyage et d'entretien.
SINGLE HANDLE DECK MOUNTED ROMAN
86543
TUB FAUCETS
LLAVES DE AGUA PARA BAÑERAS ROMANAS
CON BORDES
MITIGEURS POUR BAIGNOIRE ROMAINE -
POSE SUR PLAGE
®
?
"The Commonwealth of Massachusetts requires all hand-held shower sprays to comply with
the Massachusetts State Plumbing Code 248 CMR whereby their installation shall include a
device that limits the maximum deliverable temperature of hot water to 110°F and an approved
backflow prevention system ."
®
"La Commonwealth de Massachusetts requiere todos los aerosoles de mano de la ducha
conformarse con el código 248 CMR de la plomería del estado de Massachusetts por el que
su instalación incluya un dispositivo que limite la temperatura entregable máxima de la agua
caliente a 110°F y a un sistema aprobado de la prevención de la expulsión."
« Le Commonwealth du Massachusetts exige de tous les pulvérisateurs tenus dans la main
de douche d'être conformes au code 248 CMR de tuyauterie d'état du Massachusetts par
lequel leur installation inclue un dispositif qui limite la température livrable maximum de
86543
l'eau chaude à 110°F et à un système approuvé d'empêchement de refoulement. »
1
67114
1/8" (3.17mm)
67214
08/18/14 Rev. A
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Brizo Quiessence 67114
Summary of Contents for Brizo Quiessence 67114
- Page 1 Inscrivez le numéro de modèle ici. You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin: 1/8" (3.17 mm) 3/32" (2.38 mm) For easy installation of your Brizo ® 1/8" (3.17mm) you will need: ・To READ ALL the instructions completely before beginning.
-
Page 2: Cleaning And Care
Company para todos los reclamos a menos que el comprador haya registrado el producto con fecha de compra. No se garantizan las pilas. Delta Faucet Company. Esta garantía le aplica sólo a las llaves de agua de Brizo fabricadas ®... -
Page 3: Maintenance
Model 67114 RP42296▲ Handle with Set Screw & Button Manija con Tornillo de Ajuste y Botón Manette avec vis de calage et bouton RP42302▲ RP42282▲ Maple Wood Handle Set Screw & Button with Set Screw & Button Tornillo de Ajuste y Botón Manija de madera del arce Vis de Calage et Bouton con Tornillo de Ajuste y Botón... - Page 4 Model 67214 RP42296▲ Handle with Set Screw & Button Manija con Tornillo de Ajuste y Botón Manette avec vis de calage et bouton RP61591▲ Diverter Assembly RP42302▲ Ensamble del Desviador RP42282▲ Maple Wood Handle Dérivation Set Screw & Button with Set Screw & Button Tornillo de Ajuste y Botón Manija de madera del arce Vis de Calage et Bouton...
- Page 5 3" min. (7.6 cm) 5"- 8" (12.7 cm - 20.3 cm) 1 1/2" (38 mm) Diameter 1 1/2" (38 mm) Diameter Finished Deck (Standard) Installation Install spout adapter (1) from below. Reinstall washer (2) on spout (NOTE: Intended for surfaces up to 2 1/2" (63.5 mm) thick.) adapter.
- Page 6 Remove test cap (1) and discard. Assemble gasket (2) onto spout (3), Carefully bend corrugated outlet tube (1) and insert into elbow (2). and install spout onto spout adapter (4). OPTION: Use silicone under the Connect elbow to spout adapter (3). Connect inlet tubes (4) to water gasket if deck is uneven.
- Page 7 3" min. (7.6 cm) 5"- 8" Spout (12.7 cm - 20.3 cm) 2" (51 mm) Valve Diameter 1 1/2" (38 mm) Diameter Rough Deck (Thick Tile) Installation(NOTE: Intended for surfaces Finish surface up to cardboard spacer (1). Note: Be sure to leave access up to 2 1/2"...
- Page 8 Reinstall washer (1) on spout adapter. Rotate washer 90° to expose Remove test cap (1) and discard. Install spout with gasket (2) onto spout adapter (3). OPTION: Use silicone under the gasket if deck is uneven. screws (2). Tighten screws (2) with a regular slotted screwdriver until washer (1) is flush to the finished deck surface.
- Page 9 3" min. (7.6 cm) 5"- 8" (12.7 cm - 20.3 cm) 5"- 8" 1 1/2" (38 mm) (12.7 cm - 20.3 cm) Diameter 1 1/2" (38 mm) Diameter 1 1/2" (38 mm) Diameter Finished Deck (Standard) Installation (NOTE: Intended for surfaces up to 2 1/2" (63.5 mm) thick.) Loosen screws (1) until cardboard tube (2) is free.
- Page 10 Tighten screws (1) with a regular slotted screwdriver. NOTE: One Insert the leader hose (1) through the spray support assembly (2). Connect the leader hose (1) to the diverter outlet (3). Use Plumbe r screw can be fully tightened before the other screw is tightened. tape on threaded connections.
- Page 11 Remove set screw (1). Remove and discard test cap (2). Install gasket (3) Remove and discard the test cap and gasket (1). and spout (4) onto spout adapter (5). OPTION: Use silicone under the gasket if deck is uneven. Be sure spout is resting firmly on the deck. Slide hose (1) through conical nut (2).
- Page 12 Install base (1) onto nest (2) and tighten. OPTION: Use silicone under Pull hose (1) to its farthest extension and point it down into the tub. Pull the lift rod (2) up. Move faucet handle (3) to the full on position and flush the base if deck is uneven.
- Page 13 3" min. (7.6 cm) 5"- 8" (12.7 cm - 20.3 cm) 5"- 8" 1 1/2" (38 mm) (12.7 cm - 20.3 cm) Diameter 1 1/2" (38 mm) Diameter 1 1/2" (38 mm) Diameter Rough Deck (Thick Tile) Installation(NOTE: Intended for surfaces Finish surface up to cardboard spacers (1).
- Page 14 Insert the leader hose (1) through the spray support assembly (2). Reinstall washer (1) and nest (2) on spout. Rotate washer and nest 90° to Connect the leader hose (1) to the diverter outlet (3). Use Plumbe r expose screws (3). Tighten screws (3) with a regular slotted screwdriver tape on threaded connections.
- Page 15 Remove set screw (1). Remove and discard test cap (2). Install gasket (3) Remove and discard the test cap and gasket (1). and spout (4) onto spout adapter (5). OPTION: Use silicone under the gasket if deck is uneven. Be sure spout is resting firmly on the deck. Slide hose (1) through conical nut (2).
- Page 16 Install base (1) onto nest (2) and tighten. OPTION: Use silicone under Pull hose (1) to its farthest extension and point it down into the tub. Pull the lift rod (2) up. Move faucet handle (3) to the full on position and flush the base if deck is uneven.
Need help?
Do you have a question about the Quiessence 67114 and is the answer not in the manual?
Questions and answers