(Leuchtensteckverbinder). 2.4 Vor dem Lösen bzw. Anschließen des Lampenkabels an der Lampensteck- verbindung ist das Gerät auszuschalten. Es dürfen nur original ARRI Lampenkabel mit für die Lampenleistung zugelassenem Querschnitt zum Anschluß der Leuchte an das Vorschaltgerät verwendet werden. Der Betrieb von Leuchten anderer Hersteller als ARRI am Vorschaltgerät ist nicht zulässig.
3. Produktbeschreibung Das Elektronische Vorschaltgerät EB 1200/1800 Event Three von ARRI ist für den Betrieb von bis zu drei 1200 W oder 1800 W Scheinwerfern über ein ARRI Multicore System vorgesehen (siehe Abb. 1, Seite 16). Das Elektronische Vorschaltgerät EB 1200/1800 Event Three besteht aus drei 1800 W Modulen (siehe Abb.
4.1 Inbetriebnahme EB 1200/1800 EVENT THREE Prüfen, ob sich die ON/OFF-Schalter aller Module in der OFF-Stellung befinden Bis zu drei geprüfte ARRI 1200 W Event oder ARRI 1800 W Event Scheinwerfer über ein passendes ARRI Multicore System an das EVG anschließen (siehe Abb. 1, Seite 16).
Deutsch LICHTTECHNIK An der Frontplatte des Moduls zeigt die „1200 W“ bzw. „1800 W“ LED die aktuelle Lampennennleistung an. Das EVG startet immer im 1200 W Modus. Bei einem 1800 W Scheinwerfer wird die elektronische Lampenerkennung für die ersten 3 Minuten nach Zünden der Lampe aktiviert.
Deutsch LICHTTECHNIK 6. Störungssuche 6.1 Wird das EVG mit der richtigen Netzspannung versorgt? Der zulässige Bereich ist auf dem Typenschild vermerkt. EVG für mehrere Netzspannungsbereiche schalten automatisch um. 6.2 EVG ans Netz anschließen und den Schutzleiteranschluß am Vorschaltgerät prüfen (LED „PE“ muß leuchten). 6.3 Spannungsversorgung prüfen: Die drei LEDs "L1,"...
Disconnect EB from power supply before opening (pull out the line plug). Do not pull on the connection cable, but on the plug, to disconnect the EB from mains. Any repairs or changing of the line plug must only be carried out by qualified personnel or ARRI- service departments.
(see fig.1, page 16). The ARRI EB 1200/1800 Event Three consists of 3 modules (see fig.3, page 17). Each modul can drive one 1200 W or 1800 W luminaire.
4.1 Energizing System Check the ON/OFF Switches of all modules to be in "OFF"-position. Connect up to three properly checked ARRI 1200 W Event or ARRI 1800 W Event luminaires with a suitable ARRI Multicore System to the electronic ballast (see fig.
Deutsch LICHTTECHNIK 4.3 Control of light intensity After warming up, the light intensity of the metal halide daylight-lamp may be controlled by the dimming potentiometer (stepless). The nominal lamp power can be adjusted between 50 - 105% (left stop = MIN, right stop = MAX of power). 4.4 Remote Control DMX 512 The Electronic Ballast EB 1200/1800 Event Three can be controlled by a remote control according DMX-512 standard.
Deutsch LICHTTECHNIK 5. Technical Data Mains supply Supply Voltage 50/60 Hz; 3, N, PE (three phase) = 180 – 265 V~ Nominal Current 14.5 – 10.5 A (eff., each phase) Line Power 7.800 VA (max.) cos ϕ ≈ 0.98 Power Factor Line Connector CEE 16 A (3+N+PE) Lamp connection...
Test the module with a known good luminaire. If cables are suspect, they should be exchanged with known good cables. If a ballast is found to be faulty ideally it should be returned together with the luminaire, multicore cable and splitbox to the ARRI-service location for examination. - 15 -...
LICHTTECHNIK MULTICORE SPLITBOX ARRI Event Lampheads EB 1200/1800 Event Three HAN 16E )¹ L2.37705.0 ARRISUN 12 Event, ARRISUN 18 Event AS 12 Event AS 18 Event AS 18 Event MIXED with with with (EXAMPLE) 1200 W Lamp 1200 W Lamp...
LICHTTECHNIK DMX-Adressvergabe DMX Address Assignment Modul Nr. Module No. Dimmadresse X + 2 X + 4 Dimming Address DMX-Adressschalter / Schaltadresse X + 1 X + 3 X + 5 DMX Address Switch On/Off Address 1200/1800 W 1200/1800 W 1200/1800 W ELECTRONIC BALLAST MODULE ELECTRONIC BALLAST MODULE ELECTRONIC BALLAST MODULE...