Subscribe to Our Youtube Channel
Summary of Contents for Mac Afric TPOWDR-001
- Page 1 POWDER COATING SYSTEM ASSEMBLY AND OPERATING INSTRUCTIONS Please read this manual BEFORE using this item...
-
Page 2: Specifications
SPECIFICATIONS Item Description Power Consumption 220 VAC,50Hz Line Cord 6 feet long, 0.75mm ,3-prong grounded plug Air Supply Pressure 10 to 30 PSI Cubic Feet Per Minute 3.5 CFM at 30 PSI Air Inlet Size inch Remote Activation Switch 8 Feet long Gun Powder Lead 7 feet, high voltage lead. -
Page 3: Electrical Safety
Electrical Safety Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. - Page 4 15. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations. 16. Use safety equipment. Always wear eye, face, and breathing protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
- Page 5 SPECIFIC SAFETY RULES FOR THIS PRODUCT Maintain labels and nameplates on the Powder Coating System.These carry Important information. Always wear ANSI approved safety impact eye goggles, respirator, and heavy work gloves when using the Powder Coating System.Using personal safety devices reduce the risk for injury. Maintain a safe working environment.
- Page 6 13. Avoid powder contamination. - Protect your lungs by using an approved dust mask. - Never cure objects in an electric oven that is used for food also. - Ventilate the area well. - Wear an activated charcoal respirator when oven curing the coated object. 14.
-
Page 7: Extension Cords
Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances.The plug and outlet should look like those in the following illustration. (See Figure A.) Figure B Figure A Double Insulated Tools with Two Prong Plugs Tools with a polarized plug (one blade is wider than the other) serve as a feature to reduce the risk of electric shock.This plug will fit in a polarized outlet only one way. - Page 8 A" ("W" in Canada) to indicate it is acceptable for outdoor use. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician Before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
-
Page 9: Operation
Spray Gun (2) Three Scatter Tips (21,22,24) Two Power Cups (4) Control Box (11) Power Cord (19) Pressure Reducer Valve (8) Disposable Moisture Separator (9) Quick Adapter (10) Foot Switch (16) Ground Wire (26) And Clip (15) PREPARATION Setup an air supply with an air pressure regulator and moisture trap (do not use an in- line air oiler).The air compressor must provide an air pressure of 10 to 30 PSI. - Page 10 Unscrew the Powder Cup (4) from the Spray Gun (2) and fill with up to two inches of coating powder (not supplied). See photo below, left. a. Turn the cup open side up, and place on a clean piece of paper. b.
- Page 11 10. Press the Spray Gun Trigger (6) and Foot Switch (16) at the same time and test the spray pattern on a piece of scrap metal. The Trigger controls the air and powder flow The Foot Switch controls the electrical charge.
-
Page 12: Maintenance
Process Tips To remove an orange peel effect after curing, wet-sand the object with 400 grit sandpaper, dry, and repeat the coating process. Over-powder coating can cause this effect. Polish with traditional paint polishes. Lightly buff with a loose wheel and white rouge compound to remove imperfections. Thoroughly clean the Powder Cup (4) before changing powders. -
Page 13: Parts List
PARTS LIST Part # Description Spray Gun Pipe Spray Gun Air Outlet Pipe Powder Cup Air Input Pipe Trigger Regulating Screw Pressure Reducer Valve Disposable Moisture Separator Quick Adapter Control Box Power Indicator Light Activation Indicator Light Power Switch Ground Clip Foot Switch Fuse Foot Switch Cable... -
Page 14: Assembly Drawing
ASSEMBLY DRAWING...
Need help?
Do you have a question about the TPOWDR-001 and is the answer not in the manual?
Questions and answers