Subscribe to Our Youtube Channel
Related Manuals for Symbol CRD 2 00-1000S Series
Summary of Contents for Symbol CRD 2 00-1000S Series
- Page 1 C R D 2 x 0 0 1 0 0 0 S S i n g l e S l o t S e r i a l / C h a r g i n g C r a d l e...
- Page 2 Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
-
Page 3: About This Guide
For detailed information on any PPT 2700 or PPT 2800 terminal, refer to the Quick Reference Guide or Product Reference Guide for that terminal. For information on ordering other Symbol manuals, contact your Symbol Support Center, as listed on the back of this manual. -
Page 4: Parts Of The Cradle
Parts of the Cradle Spare Battery Charging Slot Slot for Terminal Spare Battery LED Spare Battery Terminal Status LED Charging Slot Serial Port Power Port LED Indicators Indicator Meaning Terminal Status Solid Red Terminal battery is charging. This occurs whether the terminal is on or off. Solid Green The terminal battery is fully charged. -
Page 5: Cradle Set-Up
The cradle provides power to a PPT 2700 or PPT 2800 terminal, and re-charges terminal batteries. Note: Use only a Symbol-approved power supply (p/n 50-14000- 107) output rated 9 VDC and minimum 2 Amperes. The power supply is certified to EN60950 with SELV outputs. - Page 6 municating with the cradle. For more information, see Troubleshooting on page 10 Inserting the Terminal Insert the terminal as shown below. When inserted correctly: • the bottom of the terminal fits smoothly into the cradle. • the Terminal Status LED lights up (red, if battery is charging). If the battery is fully charged, the Status LED turns green.
-
Page 7: Serial Devices
Q u i c k R e f e r e n c e 3. Connect the other end of the serial cable to the host PC. Serial Port on host PC Note: The cradle requires a dedicated serial port on the host PC. -
Page 8: Installing Communication Software
Synchronizing Data With a Host PC This section describes how to use the cradle to synchronize infor- mation between a terminal and a host PC. After you synchronize, any changes you have made on your terminal or in your desktop software appear in both places. -
Page 9: Charging The Terminal Battery
Q u i c k R e f e r e n c e partnership dialog box. The terminal should similarly indicate a “connected” status. 4. On the desktop computer, enter a unique device name for your terminal and click the Next button. Follow the instructions on the screen to set up a partnership that allows synchronization of information between the two computers. - Page 10 2. Insert the terminal in the cradle. Spare Battery LED Terminal Status LED 3. The Terminal Status LED turns red to indicate charging, then green when the battery is fully charged. If the terminal is off when being charged. the terminal’s battery will fully charge after approximately 2 1/2 hours.
-
Page 11: Charging A Spare Battery
Q u i c k R e f e r e n c e Charging a Spare Battery To charge a spare terminal battery: 1. Insert the battery into the spare battery charging slot in the back of the cradle. Spare Position it with the charging Battery... -
Page 12: Troubleshooting
Troubleshooting Symptom Possible Cause Action Terminal Status Terminal is not inserted Remove the terminal and re-insert it, LED does not correctly into the cradle. making sure it fits snugly onto the light up. connector at the bottom of the cradle. Cradle is not receiving Make sure the power input cable is power. -
Page 13: Regulatory Information
Q u i c k R e f e r e n c e Regulatory Information Radio Frequency Interference Requirements Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. - Page 14 • IEC 1000-4-3:1997; Electromagnetic Compatibility (EMC); Part 4:Testing and measurement techniques; Section 3. Radiated, radio frequency, electromag- netic field immunity test • IEC 1000-4-4:1995; Electromagnetic compatibility (EMC); Part 4: Testing and measurement techniques; Section 4:Testing electrical fast transient,/Burst immunity • IEC 1000-4-5:1995; Electromagnetic compatibility (EMC), Part 4: Testing and measurement techniques;...
-
Page 15: Warranty Coverage And Procedure
This warranty is provided to the original owner only and is not transferable to any third party. It shall not apply to any product (i) which has been repaired or altered unless done or approved by Symbol, (ii) which has not been maintained in accordance with any operating or handling instructions... -
Page 16: Service Information
Distributor Operations +44 208 945 7360 Customer support is available 24 hours a day, 7 days a week. For the latest version of this guide go to:http://www.symbol.com/manuals. 70-37807-02 Revision C — November 2001 Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300...
Need help?
Do you have a question about the CRD 2 00-1000S Series and is the answer not in the manual?
Questions and answers