Advertisement
WARRANTY ............................................................................................................................................................................... 1
INTRODUCTION & STANDARD FEATURES ........................................................................................................................... 1
THEORY OF OPERATION ......................................................................................................................................................... 2
OPTION DESCRIPTION ............................................................................................................................................................. 2
CUT-OUT & MOUNTING DIMENSIONS .................................................................................................................................... 2
MOUNTING INSTRUCTIONS .................................................................................................................................................... 2
PU-E SERIES PICK-UP INSTALLATION .................................................................................................................................. 3
DM4000 SERIES HOOK-UP & WIRING .................................................................................................................................... 3
FIELD PROGRAMMING THE DM4000 SERIES .................................................................................................................... 4-5
DECIMAL POINT SELECTION .................................................................................................................................................. 5
COMMONLY ASKED QUESTIONS ........................................................................................................................................ 5-6
SPECIFICATIONS ...................................................................................................................................................................... 6
PRODUCT LINE ................................................................................................................................................... BACK COVER
Dart Controls, Inc. (DCI) warrants its products to be free from defects in material and workmanship. The exclusive remedy for this
warranty is DCI factory replacement of any part or parts of such product which shall within 12 months after delivery to the purchaser
be returned to DCI factory with all transportation charges prepaid and which DCI determines to its satisfaction to be defective. This
warranty shall not extend to defects in assembly by other than DCI or to any article which has been repaired or altered by other
than DCI or to any article which DCI determines has been subjected to improper use. DCI assumes no responsibility for the design
characteristics of any unit or its operation in any circuit or assembly. This warranty is in lieu of all other warranties, express or implied;
all other liabilities or obligations on the part of DCI, including consequential damages, are hereby expressly excluded.
NOTE: Carefully check the control for shipping damage. Report any damage to the carrier immediately. Do not attempt to operate
the drive if visible damage is evident to either the circuit or to the electronic components.
All information contained in this manual is intended to be correct, however information and data in this manual are subject to change
without notice. DCI makes no warranty of any kind with regard to this information or data. Further, DCI is not responsible for any
omissions or errors or consequential damage caused by the user of the product. DCI reserves the right to make manufacturing
changes which may not be included in this manual.
Improper installation or operation of this control may cause injury to personnel or control failure. The control must be
installed in accordance with local, state, and national safety codes. Make certain that the power supply is disconnected
before attempting to service or remove any components!!! If the power disconnect point is out of sight, lock it in
disconnected position and tag to prevent unexpected application of power. Only a qualified electrician or service
personnel should perform any electrical troubleshooting or maintenance. At no time should circuit continuity be checked
by shorting terminals with a screwdriver or other metal device.
The Dart DM4000 Series is available in two basic field programmable models:
DM4004 - RATE BASED DISPLAY - Displays the rate of shaft rotation in RPM, GPM, FPM, etc.
DM4005 - PROCESS TIME DISPLAY - Displays the time of the process, based upon shaft rotation.
The DM4000 Series features a sturdy 1/8DIN aluminum housing with gasketed faceplate kit for panel mount. It will accept a variety
of signal inputs, and is field programmable via dip switches. The compact series provides a five position barrier terminal strip for
ease of connection and a large 1/2" four digit LED display, including customer selectable decimal points. Self-contained power
supply for transducer of +5VDC and 75mA output.
The Dart PU-E pick-up is recommended for use with the DM series, however the DM4000 will accept inputs from a variety of
transducer types. Included are hall-effect, photo-electric, magnetic, TTL, or any +5 to 24VDC device. See "Pick-up Selection Chart"
on page 3.
The DM4000 Series comes standard for a 60 Hertz signal, but can be easily changed to 50 Hertz by using the "Field Programming
Formula" on page 4. This program simply changes the time base settings, substituting 3000 for 3600 in the Field Programming
Formula. This compensates for the change in the clock frequency from 60 Hertz to 50 Hertz.
TABLE OF CONTENTS
WARRANTY
WARNING
INTRODUCTION
STANDARD FEATURES
Works in conjunction with a transducer
Operates on either a 50 or 60 Hertz signal
1
Advertisement
