1. Manuals
  2. Brands
  3. Hamilton Manuals
  4. Controller
  5. C2000
  6. Operational manual

Hamilton C2000 Operational Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

C2000 Operational Manual
Document #101-0009
1
3/09/05

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C2000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hamilton C2000

  • Page 1 C2000 Operational Manual Document #101-0009 3/09/05...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS I. INTRODUCTION ....................4 Options ............................4 II. OPERATION ......................5-6 Vend Switches ..........................5 Configuration Switches ........................5 LED ..............................5 Resetting ............................6 III. ERROR CODES ....................7-9 ERROR CODE DEFINITIONS ....................8-9 COIN DROP STUCK ....................... 8 HOPPER JAMMED ........................
  • Page 3 ABOUT THIS MANUAL This manual was designed to introduce the C2000 Controller and explain its functions and how it operates. It will also enable the operator to detect error codes and perform basic troubleshooting procedures. Included in this manual is a switch setting configuration for optional payout modes. If further assistance is needed, please call the manufacturer at (800) 837-5561 or (419) 867-4858.

  • Page 4: Introduction

    I. INTRODUCTION The C2000 Controller makes operating a Bill Changer simple. The Controller monitors the inputs from the various components and controls the Validator, Stacker and Hopper(s). It also monitors the power supply for fluctuations in current and voltage. When the customer inserts a bill, change or tokens are dispensed according to a payout scheme selected by the operator.

  • Page 5: Operation

    II. OPERATION On the face of the C2000 Controller there is a white COMPUTER RESET button, a green LED, and a bank of 12 Vend Switches. On one side is the Card Edge Connector, which is where the main wiring harness of the changer connects.

  • Page 6: Resetting

    Resetting The white COMPUTER RESET button is located on the face of the Controller. After an error has occurred, reset the computer by depressing the COMPUTER RESET button once. The LED will go out while the Controller resets. Once the controller has reset, the LED will turn back on as a steady light. Document #101-0009 3/09/05...

  • Page 7: Error Codes

    An LED that remains off indicates no power or a major failure of the Controller. In the event that a malfunction occurs, the following pages provide assistance for diagnosis. Always note the error code before attempting any service or before contacting HAMILTON. ERROR CODES 1 FLASH, PAUSE, 1 FLASH...

  • Page 8: Error Code Definitions

    ERROR CODE DEFINITIONS COIN DROP STUCK Since the coin count switch in the hopper is NORMALLY CLOSED, a coin passing under the count switch OPENS the circuit. The Controller allows only a short time for a coin to pass under and open the switch and for a coin to drop.

  • Page 9: Invalid Payout Switch Setting

    If the validator shuts down the Controller, this error will flash. For example, if a bill gets hung up on the rear sensor causing the bill to be stolen, the validator will be inhibited and will shut down the C2000 Controller. If this error flashes, check the validator display for an error message.

  • Page 10: Appendix A- Switch Settings

    APPENDIX A Switch Settings 1 and 2 Hopper Mode SWITCH SETTING MODE OF OPERATION/PAYOUTOPTIONS 1 HOPPER - TOKENS + + + + + + + + + + + 1q = 1t 10$ = 45t 1$ = 4t 20$ = 100t A B C D E F G H I J K L 5$ = 20t...
  • Page 11 SWITCH SETTING MODE OF OPERATION/PAYOUTOPTIONS 1 HOPPER - TOKENS + + + + + + + + 1$ = 4t 10$ = 48t A B C D E F G H I J K L 5$ = 20t 20$ = 100t 2 HOPPERS - QUARTERS, DIMES + + + + + + + + 1$ = 4q...
  • Page 12 SWITCH SETTING MODE OF OPERATION/PAYOUTOPTIONS 2 HOPPERS - QUARTERS, DIMES + + + + + + + + + 2q = 5d 10$ = 40q 1$ = 4q 20$ = 80q A B C D E F G H I J K L 5$ = 20q 2 HOPPERS - TOKEN, TOKEN + + + + + +...
  • Page 13 Switch Settings 3 Hopper Mode SWITCH SETTING MODE OF OPERATION/PAYOUTOPTIONS 3 HOPPERS - QUARTERS, DIMES, NICKELS + + + + + + + + 1$ = 3q+2d+1n 10$ = 38q+4d+2n A B C D E F G H I J K L 5$ = 19q+2d+1n 20$ = 76q+8d+4n 3 HOPPERS - QUARTERS, DIMES, NICKELS...

  • Page 14: Appendix B - Configuration Switch Settings

    APPENDIX B Configuration Switch Settings Document #101-0009 3/09/05...
  • Page 15 Seller further warrants all repair or service work performed by a factory trained representative or Hamilton Manufacturing Corp. for a period of ninety (90) days from the date the repair or service work was performed. Purchaser’s remedies and the liabilities and obligations of Seller herein shall be limited to repair or replacement of equipment as Seller may choose, and Seller’s obligation to remedy such defects shall not...
  • Page 16 Seller expressly disclaims any warranty for any losses due to bill manipula- tion or theft or loss of cash under any circumstances. No person or entity other than a factory trained representative or Hamilton Manufacturing Corp. has performed or attempted to perform the subject repair or service.
  • Page 17 Document #101-0009 3/09/05...
  • Page 18 Hamilton Manufacturing Corporation 1026 Hamilton Drive Holland, OH 43528 Sales Phone: (888) 723-4858 Sales Fax: (419) 867-4850 Customer Service Phone: (800) 837-5561 Customer Service Fax: (419) 867-4857 Advanced Systems Phone: (866) 296-3365 Advanced Systems Fax: (419) 867-4857 Parts Phone: (866) 835-1721 Parts Fax: (419) 867-4867 Website: http:\\www.hamiltonmfg.com...

Table of Contents

Save PDF