Subscribe to Our Youtube Channel
Summary of Contents for ANTTI 408050
- Page 1 Installation and Operating Instructions Scale 408050 (en) ANTTI-TEOLLISUUS OY Koskentie 89 25340 KANUNKI Puhelin (02) 774 4700 E-mail: antti-teollisuus.fi www.antti-teollisuus.fi 01-2020...
- Page 3 Base Base viewed from above Scale sensor Antti-Teollisuus delivers scale sensors with capacity of 20 000 kg. Thus total weight of dryer may be 80 000 kg. Slight exceeding may only cause minor inaccuracy in measuring results. To install the scale sensors, the dryer legs must be shortened by 121,5 mm (see illustra- tion on the next page).
- Page 4 Scale Antti-Teollisuus Oy 01-2020...
- Page 5 If you want to have additional functions: - Analog output card (4 – 20 mA ) for displaying the readouts also on the logic display (requires that Antti-Logicontrol is used for control centre of the dryer). Setting the parameters is instructed later in this manual.
- Page 6 Before inserting the card, check out the correct slot in the picture on the next page. After installation, put the meter back in the box and ensure that the box is properly closed. Installation kit Holder Pull Depress Protective carton VIEWED FROM SIDE Antti-Teollisuus Oy 01-2020...
- Page 7 Usually there is no need to change the jumper settings. We recommend, however, that you check the jumper settings before resuming the operation. After installation of any optional cards, put the meter back in the box and ensure that the box is properly closed. Antti-Teollisuus Oy 01-2020...
-
Page 8: Dimensions (Mm)
The analogue card makes it possible to transmit the scale readout to the panel display on the logic centre or to the PC control. The terminals 20-25 are not in use. Antti-Teollisuus Oy 01-2020... - Page 9 Scale Connecting the panel meter with two or four sensors. (Note! If you are using four sensors, you need a connecting box). CONNECTING THE SCALE; 2 SENSORS SCALE DISPLAY SCALE SENSORS Antti-Teollisuus Oy 01-2020...
- Page 10 Scale CONNECTING THE SCALE; 4 SENSORS SCALE DISPLAY CONNECTING BOX SCALE SENSORS Antti-Teollisuus Oy 01-2020...
-
Page 11: Programming Basics
Programming menu 5. Resuming the factory settings and adjustment of brightness. * Option In addition to the operations described here, the meter comes with numerous other func- tions. Please refer to the manual delivered with the meter for more information. Antti-Teollisuus Oy 01-2020... -
Page 12: Programming Diagram
Antti-Teollisuus Oy 01-2020... - Page 13 Displays the readout of the summarizing counter Indicates the status of the preset value 1 (ON/OFF) Indicates the status of the preset value 2 (ON/OFF) Indicates the status of the preset value 3 (ON/OFF) Indicates the status of the preset value 4 (ON/OFF) Antti-Teollisuus Oy 01-2020...
- Page 14 Finally depress the DSP key to resume the display mode. If you get lost or confused during the procedure, press the DSP key to restart. The next step is basic calibration of the scale under programming menu 1. Antti-Teollisuus Oy 01-2020...
- Page 15 (key tai apLy) Defining the setting based on current styLe apLy signal (apLy) Present signal value of the first calibra- **** tion point (1NP 1). Write down the value 1Np 1 in the adjacent table. Antti-Teollisuus Oy 01-2020...
- Page 16 *** While depressing the key in combination with the keys, the value will change by 1 000 every time the key is depressed **** Value that depends on the instance Antti-Teollisuus Oy 01-2020...
- Page 17 Additional operation for 2nd function key, Sc-F2 no changes Moving to programming mode (PRO) or returning to start mode (NO) Exiting the programming mode *Only, if a printer is connected to the serial communication port on the scale terminal. Antti-Teollisuus Oy 01-2020...
- Page 18 (no, odd, even) Set address to 0. Addr Accept transfer of abbreviation by select- Abrv ing "yes" Select "no" for parameters to be printed. Moving to programming mode (PRO) or returning to start mode (NO) Exiting the programming mode Antti-Teollisuus Oy 01-2020...
- Page 19 80000 Change the value to 80000 using the buttons Refreshing rate for output signal. Change the value to 2.0s using the buttons Moving to programming mode (PRO) or returning to start mode (NO) Exiting the programming mode Antti-Teollisuus Oy 01-2020...
- Page 20 9-fCS Adjust brightness of the display, d-Lev ing buttons (0-15) Use code 66 for resetting the factory Code settings, select using buttons Moving to programming mode (PRO) or returning to start mode (NO) Exiting the programming mode Antti-Teollisuus Oy 01-2020...
-
Page 21: Fault Finding
* Upon starting the meter performs a self-test. If the operation is not correct, an error code (Err 1, Err 2, Err 3, Er 4 ja Err 5) is shown on the display. If an error code is shown on the display, contact the supplier of the device. Antti-Teollisuus Oy 01-2020... -
Page 22: Guarantee Terms
Scale GUARANTEE TERMS Antti-Teollisuus Oy grants a guarantee on the products the company has manufactured, subject to the follow- ing terms: The guarantee lasts for one year, starting on the date of delivery from the factory; however, it must include at least one harvesting season. - Page 23 Scale EU Declaration of Conformity ANTTI-TEOLLISUUS OY Koskentie 89 FI-25340 KANUNKI Tel.: +358 2 7744700 declares that SCALE conform with the provisions of the following directives: - Machine Directive 2006/42/EU Kuusjoki 03.01.2020 Kalle Isotalo Managing Director Antti-Teollisuus Oy 01-2020...
Need help?
Do you have a question about the 408050 and is the answer not in the manual?
Questions and answers