Related Manuals for ETAS CBEB100.1-1m0
Summary of Contents for ETAS CBEB100.1-1m0
- Page 1 CBEB100.1-1m0 CBEB100.1-1m0 - Slave CBEB105.1-1m0 CBEB105.1-1m0 - Slave Media Converter User’s Guide www.etas.com...
- Page 2 The data in this document may not be altered or amended without special noti- fication from ETAS GmbH. ETAS GmbH undertakes no further obligation in relation to this document. The software described in it can only be used if the customer is in possession of a general license agreement or single license.
-
Page 3: Table Of Contents
Cabling ..............19 4.2.1 Cabling of CBEB100.1-1m0 / CBEB100.1-1m0 - Slave ....19 4.2.2 Cabling of CBEB105.1-1m0 / CBEB105.1-1m0 - Slave . - Page 4 ETAS Contact Addresses ........
-
Page 5: About This Document
ETAS About this Document About this Document Classification of Safety Messages The safety messages used here warn of dangers that can lead to personal injury or damage to property: DANGER indicates a hazardous situation with a high risk of death or serious injury if... -
Page 6: Typographical Conventions
Additional cables and adapters can be obtained separately from ETAS. A list of available accessories and their order designation is located in chapter “Order- ing Information” on page 29 of this manual or in the ETAS product catalog. CBEB10x.1-1m0 - User’s Guide... -
Page 7: Basic Safety Notices
• “Intended Use” on page 7. General Safety Information Please observe the Product Safety Notices ("ETAS Safety Notice") and the fol- lowing safety notices to avoid health issues or damage to the device. NOTE Carefully read the documentation (Product Safety Advice and this User's Guide) that belongs to the product prior to the startup. - Page 8 ETAS Basic Safety Notices Requirements for the technical state of the product The product is designed in accordance with state-of-the-art technology and recognized safety rules. The product may be operated only in a technically flaw- less condition and according to the intended purpose and with regard to safety and dangers as stated in the respective product documentation.
- Page 9 • Adhere to the maximum permissible cable lengths! • Do not use any damaged cables! Cables may be repaired only by ETAS! CAUTION Never apply force to insert a plug into a socket. Ensure that there is no contamination in and on the connection, that the plug fits the socket, and that you correctly aligned the plugs with the connection.
- Page 10 Prior to the transport, disconnect the cables from the product. Maintenance The product is maintenance-free. Repair If an ETAS hardware product should require a repair, return the product to ETAS. Cleaning the module housing • Use a dry or lightly moistened, soft, lint-free cloth for cleaning the module housing.
-
Page 11: Hardware Description
Description Fig. 3-1 Media Converter CBEB100.1-1m0 (left) and CBEB105.1-1m0 (right) Media Converter CBEB100.1-1m0 and CBEB105.1-1m0 are set up as masters by default. Media Converter CBEB100.1-1m0 - Slave and CBEB105.1-1m0 - Slave are set up as slaves by default. The Media Converters CBEB100.1-1m0 and CBEB105.1-1m0 are functionally identical. -
Page 12: Design
Do not open or modify the product housing! Work on the product housing may be performed only by qualified technical personnel. 3.2.2 Connections CBEB100.1-1m0 / CBEB100.1-1m0 - Slave Fig. 3-2 Connections CBEB100.1-1m0 / CBEB100.1-1m0 - Slave No. in Fig. 3-2... -
Page 13: Connections Cbeb105.1-1M0 / Cbeb105.1-1M0 - Slave
ETAS Hardware description 3.2.3 Connections CBEB105.1-1m0 / CBEB105.1-1m0 - Slave Fig. 3-3 Connections CBEB105.1-1m0 / CBEB105.1-1m0 - Slave No. in Fig. 3-2 Connection Protocol D-SUB9 Automotive Ethernet LEMO 1B Standard Ethernet CBEB10x.1-1m0 - User’s Guide... -
Page 14: Leds
Standby (0.1 s on / 1.9 s off) Flashing red Boot error - restart required: CBEB100.1-1m0 / CBEB100.1-1m0 - Slave: Disconnect the cable from the DSUB9 plug for 5 CBEB105.1-1m0 / CBEB105.1-1m0 - Slave: Disconnect the LEMO plug from the module for 5 s. -
Page 15: Functions
Fig. 3-4 Block Diagram CBEB100.1-1m0 / CBEB100.1-1m0 - Slave The CBEB100.1-1m0 / CBEB100.1-1m0 - Slave Media Converter features an Automotive Ethernet interface at the D-SUB9 plug as well as a Standard Ether- net interface (IEEE 802.3) at the RJ45 plug. -
Page 16: Block Diagram Cbeb105.1-1M0 / Cbeb105.1-1M0 - Slave
5 minutes, it switches to standby mode. 3.3.4 Master-Slave Configuration To configure the media converters CBEB100.1-1m0 and CBEB105.1-1m0 as slave or CBEB100.1-1m0 - Slave and CBEB105.1-1m0 - Slave as master, please contact your ETAS contact partner. CBEB10x.1-1m0 - User’s Guide... -
Page 17: Startup
• “Cabling” on page 19 Cabling Example CBEB100.1-1m0 / CBEB100.1-1m0 - Slave Connection of CBEB100.1-1m0 / CBEB100.1-1m0 - Slave to BR_XETK and directly to a PC. Fig. 4-1 Connection of CBEB100.1-1m0 / CBEB100.1-1m0 - Slave to BR_XETK and directly to a PC... -
Page 18: Fig. 4-2 Connection Of Cbeb105.1-1M0 / Cbeb105.1-1M0 - Slave To Br_Xetk Via Es59X
Cable for the "FE-HOST" connection CBE100 Cable for the "7-29 V DC" connection CBP120, CBP1205 Cable for the connection “ECU with BR_XETK” CBEB120 Cable for the connection “ECU with BR_XETK” (customer-specific - Please contact your ETAS con- tact partner.) CBEB10x.1-1m0 - User’s Guide... -
Page 19: Cabling
4.2.2 describe the startup in an energized cabling system. 4.2.1 Cabling of CBEB100.1-1m0 / CBEB100.1-1m0 - Slave You can startup the CBEB100.1-1m0 with ETAS cables or with customized cables: Startup of CBEB100.1-1m0 / CBEB100.1-1m0 - Slavewith ETAS cables 1. Connect the D-SUB9 plug of the Media Converter with the cable CBEB121. - Page 20 ETAS Startup Startup of CBEB105.1-1m0 / CBEB105.1-1m0 - Slave with customized cables 1. Connect the LEMO plug of the Media Converter with an ETAS Bus Interface Module oder with a Network Module. The ON ER LED lights green. The HOST LED lights yellow.
-
Page 21: Troubleshooting
Disconnect the LEMO plug from the module for 5 s. You have just Hardware error: restarted the Media If the LED continues to perma- Converter? nently flash even after a reboot, send the product to ETAS. CBEB10x.1-1m0 - User’s Guide... -
Page 22: Technical Data
ETAS Technical Data Technical Data This chapter contains information on the following topics: • “General Data” on page 22 • “RoHS Conformity” on page 23 • “CE Marking” on page 24 • “Product Return and Recycling” on page 24 •... -
Page 23: Environmental Conditions
RoHS Conformity 6.2.1 European Union The EU Directive 2011/65/EU limits the use of certain dangerous materials for electric and electronic devices (RoHS conformity). ETAS confirms that the product meets this directive applicable in the European Union. CBEB10x.1-1m0 - User’s Guide... -
Page 24: China
RoHS label attached to the product or its packaging. CE Marking With the CE mark attached to the product or its packaging, ETAS confirms that the product corresponds to the product-specific, applicable European Direc- tives. The CE Declaration of Conformity for the product is available upon request. -
Page 25: System Requirements
ETAS Technical Data System Requirements CBEB100.1-1m0 The Media Converter CBEB100.1-1m0 can be connected directly to the PC or to modules with a Fast-Ethernet-interface, e.g. • ES510 • ES511 • ES512 CBEB105.1-1m0 The Media Converter CBEB105.1-1m0 can be connected to modules with a Fast-Ethernet-interface, e.g.:... -
Page 26: Cbeb100.1-1M0 / Cbeb100.1-1M0 - Slave: Rj45 Plug
ETAS Technical Data 6.7.2 CBEB100.1-1m0 / CBEB100.1-1m0 - Slave: RJ45 Plug Fig. 6-4 Pin Assignment RJ45 Plug Signal Meaning receive, positive receive, negative send data, positive not connected not connected send data, negative not connected not connected 6.7.3 CBEB105.1-1m0 / CBEB105.1-1m0 - Slave: LEMO Plug Fig. -
Page 27: Cables And Accessories
Ethernet Adapter Cable 7.1.1 CBAE210.1 CBAE210.1-0m5 F-00K-109-930 Fig. 7-1 Ethernet Adapter Cable CBAE210.1 CBAE210.1 is an Ethernet adapter cable to connect the CBEB100.1-1m0 with an ES59x or ES600 Switch Modules, without propagation of the ETAS hardware synchronization. Product Length Order Number CBAE210.1-0m5... -
Page 28: Cbeb121.1
Automotive Ethernet Cable CBEB121.1 The CBEB121.1 cable is a Automotive Ethernet cable to connect a CBEB100.1- 1m0 / CBEB100.1-1m0 - Slave Media Converter with a BR_XETK cable adapter (e.g. CBAM290.1) plus safety banana plugs to supply the media converter. Connector... -
Page 29: Ordering Information
Order Number CBEB100.1-1m0 Media Converter, CBEB100.1-1m0 F-00K-110-094 D-SUB - RJ45 (9mc-8mc), 1m Package Contents - CBEB100.1-1m0 Media Converter - List “Content of this Package” - ETAS Safety Advice CBEB10x - China_RoHS-leaflet_Compact_green_cn NOTE Cables are not part of the scope of supplies of the Media Converter and must be ordered separately (see chapter 8.5 on page 30). -
Page 30: Cbeb105.1-1M0
(see chapter 8.5 on page 30). Accessories NOTE We recommend to use ETAS cables or any other cables certified by the stan- dards for the application. Adhere to the maximum permissible cable lenghts! CBEB10x.1-1m0 - User’s Guide... -
Page 31: Cables
ETAS Ordering Information 8.5.1 Cables Order name Short Name Order Number Ethernet Connection Adapter Cable CBAE210.1-0m5 F-00K-109-930 100MBit/s, RJ45 - Lemo 1B FGF (8fc- 8mc), 0m5 100 Mbit/s Automotive Ethernet Inter- CBEB120.1-3 F-00K-111-111 face Cable for CBEB105, Lemo 1B FGA -... -
Page 32: Etas Contact Addresses
Germany Internet: www.etas.com ETAS Subsidiaries and Technical Support For details of your local sales office as well as your local technical support team and product hotlines, take a look at the ETAS website: ETAS subsidiaries Internet: www.etas.com/en/ contact.php ETAS technical support Internet: www.etas.com/en/... -
Page 33: Figures
Media Converter CBEB100.1-1m0 (left) and CBEB105.1-1m0 (right) ..11 Fig. 3-2 Connections CBEB100.1-1m0 / CBEB100.1-1m0 - Slave ....12 Fig. 3-3 Connections CBEB105.1-1m0 / CBEB105.1-1m0 - Slave . -
Page 34: Index
Environmental Conditions ... .23 ETAS Contact Addresses ... . .32 Functions ......15 General Data .
Need help?
Do you have a question about the CBEB100.1-1m0 and is the answer not in the manual?
Questions and answers