Subscribe to Our Youtube Channel
Summary of Contents for LRS LineShare PRO
- Page 1 LineShare PRO O P E R AT O R ’ S G U I D E Installation, Warranty and Service Information Long Range Systems, Inc. 4550 Excel Parkway, Suite 200 ddison, TX 75001 800.437.4996 www.pager.net •...
-
Page 2: Table Of Contents
Table Of Contents Introduction to the LineShare PRO ........ -
Page 3: Important Notes
Warranty ............Long Range Systems LineShare PRO... -
Page 4: Introduction To The Lineshare Pro
INTRODUCTION TO THE LINESHARE PRO The LineShare Pro PRO is a telephone line management system that directs incoming phone calls to 1 of 4 destinations. It is capable of transferring calls in virtually many configurations of telephone devices includ- ing the following:... - Page 5 If telephones are connected to the LineShare Pro 104, calls without tones will transfer directly to the designated telephone. utomatic operation (calls are answered and processed where the LineShare Pro 104 is located) nswers... the call automatically. Transfers... calls to the predesignated telephone de- vice(s) according to the tone(s) received from the call- ing telephone device.
-
Page 6: Connecting The Lineshare Pro
Once you select your set-up, proceed with connecting the LineShare Pro 104. For more information on op- erating procedures, see "Using the LineShare Pro 104." Wall Mounting the LineShare Pro PRO The LineShare Pro 104 may be mounted on a wall with the connected telephone line cords above or below the unit. NOTE: Do not place the LineShare Pro 104 in close proximity to any peripheral equipment (approxi- mately 2 feet from all electronic equipment). -
Page 7: Ports On The Lineshare Pro
Ports on the LineShare Pro 104 The rear panel of the LineShare Pro 104 includes 5 modular ports and a power input port, as shown: typical installation (voice, fax, modem) would connect telephone equipment as follows: 1. Connect the provided modular line cord from a standard telephone (wall) jack to this port. -
Page 8: Installation On A Telephone System Using A 66 Block
SINGLE LINE INST LL TION ON LINE 1 For use in the utomatic mode to allow the LineShare Pro 104 control over all phones on the line. The following diagram shows an installation at the point of demarcation (DEM RC) on line 1. Once con- nected in this configuration, the telephones will not ring on an inbound call if the LineShare Pro 104 trans- fers the call to port P2, port P3 or port P4. -
Page 9: Installation With A Single Telephone Line
If you have a stand alone Caller ID device, simply plug the device into the Primary port (port P1 default), and then plug the phone into the Caller ID. The factory setting for Caller ID operation is ON. See "Program- mable features of the LineShare Pro 104" for more information. Long Range Systems LineShare PRO... -
Page 10: Connecting The Lineshare Pro To A Dsl Phone Line
The LineShare Pro 104 can also be configured (on all ports or individu- ally) to ignore inbound calls depending on application requirements.also manually reset the LineShare 3.1... -
Page 11: Typical Connection For A Small Or Home Offive
P4 - 1300Hz Modem calling tone or # 4 4 In this application, the LineShare Pro 104 will provide Emergency Call Override to the Primary port (port P1 is default) if the phone company three-way calling has been activated. See the section "Emergency Call Over- ride"... -
Page 12: Operation
The access codes and routing tones can be changed through programming. The LineShare Pro 104 will ring the Primary port up to 6 times (Rings to port P1 in this example). If the call remains unanswered after 6 rings, the LineShare Pro 104 transfers ( utomatic No nswer Transfer) the call to the Secondary port. -
Page 13: Semi- Utomatic Mode
The routing tones and access codes can be changed through programming. The LineShare Pro 104 will ring the Primary port up to 6 times (Rings to port P1 in this example). If the call remains unanswered after 6 rings, the LineShare Pro 104 will transfer ( utomatic No nswer Transfer) the call to the Secondary port. -
Page 14: Distinctive Ring Service
(long-long-short) NOTE: If a ring burst is not assigned to a port, the LineShare Pro 104 will not answer a call ringing with that specific cadence. (These settings are the default settings for transferring calls and can be changed to meet end-user needs.) -
Page 15: Distinctive Ring Service - Utomatic Mode
If the LineShare Pro 104 detects any of these signals, it transfers the call to the appropriate port. If the Line- Share Pro 104 does not detect any of these signals, it will transfer the call to the port designated in the DRS ssignment. -
Page 16: Distinctive Ring Service - Semi- Utomatic Mode
If the LineShare Pro 104 detects any of the above signals, it transfers the call to the appropriate port. Other- wise, it remains on line until it receives transfer codes, or the call disconnects. -
Page 17: Special Operating Note
Receiving a Computer Call To have the calling modem automatically "over dial" an access code for a port of the LineShare Pro 104, the caller should take into consideration whether the call is local or long distance. For remote access to port P3... -
Page 18: Computer Calls Using Distinctive Ring Service From The Telephone Company
Share Pro 104 transfers the call as described in the section Distinctive Ring service. Intercom FIf the LineShare Pro 104 is installed with phones connected to all ports, this feature also allows an intercom path between ports. To make an internal call to another port, perform the following procedures: 1. -
Page 19: Comscan Scanning/Intercom
Placing an Outbound Call Outbound calls can be placed from any port. If another port is in use, the LineShare Pro 104 will produce a busy signal when attempting to place a call from a different port. During an outbound call, you can also re- ceive a fax transmission from someone that is ready to transmit. -
Page 20: Emergency Call Override
# key must be pressed and released to activate the Emergency Call Override. Upon detection of the # key, the LineShare Pro 104 will disconnect the active port from the phone line, transmit a tone for 3 seconds, and then hook-flash to obtain dial tone from the phone company. -
Page 21: Programming
Programming the LineShare Pro 104 Introduction The LineShare Pro 104 has many programmable features and settings that can be used to customize its op- eration for your specific application. Many of these features have either feature settings and/or timing parameters associated directly with their operation. -
Page 22: Programmable Features Of The Lineshare Pro
From the remote location, dial the phone number of the line connected to the LineShare Pro 104. The call must be placed from a tone phone that has the # and * keys. When the LineShare Pro 104 answers the call, and between the ring signals, press the # key, followed by the Security ccess Code. -
Page 23: Programming Feature Settings Of The Lineshare Pro
Programmable Features of the LineShare Pro 104 Feature Number FE TURE F CTORY SETTING Programming Digits utomatic No nswer Transfer utomatic Primary Port Transfer utomatic Ring Reduction utomatic Ring Reduction Reset Extension Detection On-Line Extension Protection nswer ny Port Not Used... -
Page 24: Utomatic No Nswer Transfer
Semi- utomatic mode The LineShare Pro 104 rings the Primary port 6 times (Rings to Ports P__). If the call remains unanswered after 6 rings, the LineShare Pro 104 transfers the call to the Secondary port. - Page 25 30 seconds (Primary Port Transfer Timer) the LineShare Pro 104 will transfer the call to the Secondary port (P2 is the factory setting). If the call is on line for more than 30 seconds, the LineShare Pro 104 will simply reset for the next call when the answering machine disconnects.
-
Page 26: Utomatic Ring Reduction Reset
Ring Reduction Reset This feature is designed to reset the LineShare Pro 104 to allow 6 rings (Rings to Ports P__) to the Primary port after the utomatic Ring Reduction reduced the ring count to 2 rings. The utomatic Ring Reduction Reset will reset the ring count to the number of rings specified for the desig- nated Primary port after 10 minutes (setting of Ring Reduction Reset Timer) of inactivity. -
Page 27: On-Line Extension Protection
For an incoming call, the nswer ny Port feature permits any port that is not ringing to answer the call. Once the call is answered, the LineShare Pro 104 listens for tone access codes to transfer the call to another port. -
Page 28: Pound Key Transfer Required
3. Hang up the phone Pound Key Transfer Required This feature allows the LineShare Pro 104 to require the # key be entered before the transfer code for a port or for entering the remote programming mode using the Security ccess Code. -
Page 29: Fax Cng (Calling) Tone Detection
Mode fter the LineShare Pro 104 answers a call, the telephone line is monitored for the CNG tone and the call is transferred to the designated port if detected. The port is determined by the Port Tone ssignment parame- ter. -
Page 30: Modem Tone Detection
Mode fter the LineShare Pro 104 answers a call, the telephone line is monitored for a 1300 Hz tone and the call is transferred to the designated port if detected. The port is determined by the Port Tone ssignment parame- ter. -
Page 31: Caller Id Retransmission
Mode When the LineShare Pro 104 is in the utomatic mode, the first ring of a call passes directly to the Primary port. Between the first and second rings, the Caller ID device will display its information. The LineShare Pro 104 answers the call before the start of the second ring and processes the call normally. -
Page 32: Emergrancy Call Override
The factory setting for Emergency Call Override is set to go on-hook for 2.2 seconds [# * (three beeps) 0 1 5 * (three beeps) * (one beep) ] To set the LineShare Pro 104 for operation with the 3-way calling feature (LineShare Pro 104 performs a flash), use the following steps: 1. -
Page 33: Operationg Mode
P1, the second digit represents port P2, the third digit represents port P3, the fourth digit represents port P4. The LineShare Pro 104 cannot be set to transfer any tone to more than one port. Following are the digits that represent the tones for setting port designations:... -
Page 34: Rings To Nswer Call
This feature determines how many times an incoming call rings before it is answered by the LineShare Pro 104. To configure the LineShare Pro 104 to answer and transfer calls as quickly as possible, the factory set- ting is 1 ring, Under normal circumstances, it is not necessary to change this setting. The range of this set- ting is 1 to 30 rings. -
Page 35: Rings To Port P1
3. Hang up the phone Rings to Port P1 This feature determines the number of rings that the LineShare Pro 104 provides to port P1 with a range of 0-30 rings and operates in either the utomatic mode or the Semi- utomatic mode. -
Page 36: Rings To Port P4
Rings to Port P4 This feature determines the number of rings that the LineShare Pro 104 provides to port P4 with a range of 0-30 rings and operates in either the utomatic mode or the Semi- utomatic mode. The factory setting for the Rings to Port P4 is 6 rings. -
Page 37: Single Tone Detection Timer
Single Tone Detection Timer This feature designates the timing parameters for operation of the Single Tone Detection feature. When Single Tone Detection is activated, but this timer expires on a call, the LineShare Pro 104 will not trans- fer calls producing identifying tones. -
Page 38: Port P2 Transfer Code
The Port P2 Transfer Code can be any numeric 1-4 digits not including the # key. See Pound Key Transfer Re- quired for use with the Port P2 Transfer Code. Do not use a code that is a transfer code for another port on the LineShare Pro 104. The factory setting for the Port P2 Transfer Code is 2 2. -
Page 39: Primary Port Selection
This feature designates where the call is routed when tone transfer codes are not detected in the utomatic mode, or any inbound call when the LineShare Pro 104 is in the Semi- utomatic Mode. Calls can be desig- nated to any of the 4 ports other than the Secondary Primary Port Selection. ny of the 4 ports can be des- ignated as the Primary Port. -
Page 40: Drs Ssignment
(Long long short) The LineShare Pro 104 looks for a 4-digit entry to set the port designations for the individual rings. The first digit represents port P1, the second digit represents port P2, the third digit represents port P3, and the fourth digit represents port P4. -
Page 41: Regulatory Compliance Information
REGULATORY COMPLIANCE INFORMATION The LineShare Pro 104 complies with Part 68 of the FCC rules and the requirements adopted by the CT . On the underside of this equipment is a label that contains, among other information, a product identifier in the format US: EQ##TXXXX. - Page 42 C UTION: hanges or modifications not expressly approved by the manufacturer could void the user's authority to operate the LineShare Pro 104. Industry Canada Information - "Notice: The Industry Canada label identifies certified equipment. This certifi- cation means that the equipment meets telecommunication network protective, operation and safety re- quirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s).
-
Page 43: Warranty
If this product should become defective within the war- ranty period, we will repair or replace it with an equivalent product, free of charge. LRS will return your product via UPS ground shipping. ll warranty claims must be initiated through our customer service department.
Need help?
Do you have a question about the LineShare PRO and is the answer not in the manual?
Questions and answers