1. Manuals
  2. Brands
  3. JMband Manuals
  4. Printer
  5. JMB4+
  6. User manual

JMband JMB4+ User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
T4+ series user's manual
Version: 1.2

Advertisement

Table of Contents
loading

Summary of Contents for JMband JMB4+

  • Page 1 T4+ series user’s manual Version: 1.2...

  • Page 2: Table Of Contents

    Table of contents 1. Introduction ......................3 1.1 In the box ...................... 3 1.3 JMB4+ Printer Features ................4 1.3.3 JMB4+ Front view ................4 1.3.4 Rear view .................... 4 1.3.5 Interior view ..................5 2. Getting start ......................6 2.1 Loading the ribbon ..................

  • Page 3: Introduction

    Introduction 1.1 In the box After unpacking, please inspect carefully and make sure that you receive all the necessary parts as below:  Prin te r  Core f or f oil t a ke -up  Quick start guide ...

  • Page 4: Jmb4+ Printer Features

    1.3 JMB4+ Printer Features 1.3.3 JMB4+ Front view 1.3.4 Rear view JMB4+ user’s manual...

  • Page 5: Interior View

    1.3.5 Interior view JMB4+ user’s manual...

  • Page 6: Getting Start

    2. Getting started 2.1 Loading the ribbon 1. Pulling the release latches on two sides toward the front of printer to open the printer cover. 2. Open the ribbon cover by pushing the ribs (as shown in green) of ribbon cover.
  • Page 7 3. Insert the ribbon roll to the supply spindle. 4. Rotate the supply hub until the notches align and lock in to the left side of supply hub. JMB4+ user’s manual...
  • Page 8 5. Insert an empty media core into the take up spindle. Rotate the take up hub until the notches align and lock on the left side of take up hub. 6. Pull the ribbon out from the roll and stick it with the adhesive tape on the empty ribbon take up core.
  • Page 9 7. Rotate the take up hub on the left side of ribbon spindle till the ribbon is pulled tight. JMB4+ user’s manual...
  • Page 10 Note: The loading path of ribbon roll (outside wound) JMB4+ user’s manual...

  • Page 11: Loading The Media

    2.2 Loading the media Whether the roll media is inside or outside wound, they could be used in this printer and loaded in the same way. 1. Open the printer cover by pulling the release latch toward the front of printer.
  • Page 12 3. Pull the media so it could extend out the printer. Please make sure the printing surface is facing up. 4. Before pushing the media under the guides, adjust the label gap senor to appropriate position to detect the labels with gap, hole or black mark. JMB4+ user’s manual...
  • Page 13 5. Push the media under the both sides of guides. Note: The loading path of label roll (inside and outside wound) JMB4+ user’s manual...

  • Page 14: Jmb4+ Connecting Interfaces

    2.4 JMB4+ Connecting interfaces The following interfaces could be connected to PC to operate the printer: 2.4.1 USB Slave 2.4.2 Ethernet (Option) JMB4+ user’s manual...

  • Page 15: Power On The Printer

    2.5 Power on the printer 1. Make sure the printer power switch is off 2. Plug the power connector into the power socket at the rear side of printer. 3. Plug the power cord on the power outlet. 4. Turn the printer power switch to on. Caution.

  • Page 16: Jmb4+ Control Panel

    2.6 JMB4+ Control Panel The key functions are available under the printer READY mode: Button Appearance Function Press once Feed a blank label Press for 3 seconds to Label calibration purple light Press for 6 seconds to Print self-test page blue light Press for 9 seconds Factory default...
  • Page 17 Press over Cancel seconds The key functions are available under the printer Auto form mode: Button Appearance Function Continuously press Cancel the auto form when turning on the printer LED light Button Image Function ⚫ Flash in red light Label out ⚫...
  • Page 18 Flash in blue light Print self-test page after purple light Constantly flash Auto form mode purple light Rapidly flash in purple Reset to factory default light JMB4+ user’s manual...

  • Page 19: Printer Options

    3. Printer options 3.1 Peeler installation (Optional, not supplied) 1. Push the platen bearing tabs on the right and left sides upwards and rotate them backwards to the end. JMB4+ user’s manual...
  • Page 20 2. Lift vertically the platen from the bottom case of printer. 3. Lift vertically the front cover from the bottom case of printer. JMB4+ user’s manual...
  • Page 21 4. Insert the peeler cable to printer. (Please follow the correct connector side as figure shown to insert the cable) 5. Insert firstly the right side of peeler module to the relative holes of printer (arrow 1), press the lower part of left side of module (arrow 2), then push the left side of module to the relative holes of printer to fix firmly the peeler module on printer (arrow 3).
  • Page 22 6. Screw up the metal plate on the platen. The metal plate with arrow symbol is upward side. 7. Put the platen screwed with metal plate back to printer. 8. Assure the platen is fixed firmly in printer. JMB4+ user’s manual...
  • Page 23 9. Push the platen bearing tab forward to lock the platen. 10. Lead the label through the back of peel-off bar, as figure show. JMB4+ user’s manual...
  • Page 24 11. Close the top cover (T4+) (JMB4+) JMB4+ user’s manual...
  • Page 25 12. Pull the label to the direction as the figure show, then push the peel-off panel back to printer. 13. Press the Feed button to test the peeler function. Note: The transfer board need to be installed before installing the peeler kit.

  • Page 26: Cutter Installation (Optional, Not Supplied)

    3.2 Cutter installation (Optional, not supplied) 1. Push the platen bearing tabs on the right and left sides upwards and rotate them backwards to the end. JMB4+ user’s manual...
  • Page 27 2. Lift vertically the platen from the bottom case of printer. 3. Lift vertically the front cover from the bottom case of printer. JMB4+ user’s manual...
  • Page 28 4. Connect the cutter cable to printer. 5. Slide vertically the hooks of cutter both side into the slot. JMB4+ user’s manual...
  • Page 29 6. Push the cutter hooks to the bottom of two hooks slots, and make sure that lower hooks are fixed firmly on the hooks holes. 7. Put the platen back in the printer. JMB4+ user’s manual...
  • Page 30 8. Lock the platen bearing tabs. 9. Thread the label through the cutter inside slot and press the label under the media guides. JMB4+ user’s manual...
  • Page 31 10. Close the printer top cover. Note: The transfer board needs to be installed before installing the cutter. Please do not touch or insert your fingers into the cutter mouth while cutter is active. It will cause extremely hurt. JMB4+ user’s manual...

  • Page 32: Specifications

    4. Specifications 4.1 JMB4+ general specifications Model JMB4+ X4e+ X4De+ JMB4+ Resolution 203/300 dpi Print mode Direct Thermal/Thermal Transfer 32-bit CPU Memory RAM: 128MB SDRAM RAM: 64MB SDRAM ROM: 128MB Flash ROM ROM: 128MB Flash ROM Expendable slot for Micro SD card (up to 32GB) Print speed...
  • Page 33 Ribbon OD: 1.535” (39mm) Max length: 100m Width: 1.0” (25.4mm) to 4.3” (110mm) ID: 0.5” (12.7mm) Ribbon type: Wax, wax/resin, resin Interfaces USB slave port USB slave port USB master port Option: Serial port RS-232, Ethernet port Serial port RS-232 10/100Mbps, Bluetooth Option: Ethernet...
  • Page 34 Printer Width: 200.00mm (7.83”) dimension Length: 263.19mm (10.36”) Height: 188.29mm (7.41”) Weight: 2KG Certification CE, FCC class A, CB, CCC, BSMI JMB4+ user’s manual...

  • Page 35: Usb Port Pin Assignment

    4.2 Universal Serial Bus (USB) port pin assignment Connector type: Type A and B USB A (Master) USB B (Slave) Function VBUS Note: Master VBUS provides +5V max current 500mA. Slave VBUS is N/C. For more information about USB, please visit the website: www.usb.org.

This manual is also suitable for:

T4+ seriesX4e+X4de+

Table of Contents