Advertisement
Operation
TM
If you are installing the entire Z-Wave
system for the first time, please refer to the installation guide of
TM
Z-Wave
Interface Controller before installing ZL7261.
1.
LED Status:
After Power On, LED will keep flashing Red & Green if ZL7261 has not been included yet.
After Power On, LED will flash the color what power is loading if ZL7261 has been included.
Power Loading vs LED Color
LED Color
Plug Type E, F & L
Green
0~3A
Green+Red
3~7A
Red
7A~
For "Inclusion" in (adding to) a network: Put the Z-Wave
2.
and following its instruction to add the ZL7261 into your controller. To get in the "Inclusion" mode.
By power up to get included for first time, press the Program switch 3 times within 3 seconds to
be included.
For "Exclusion" from (removing from) a network: Set up the Z-Wave
"exclusion" mode, and following its instruction to delete the ZL7261 from your controller. Press the
Program Switch 3 times within 3 seconds to be excluded.
For "Association": the Z-Wave
TM
interface controller set "Association", and following its instruction
to associate the ZL7261 with other device. Support one group (5 nodes). ZL7261 will report back
every time ON and OFF status and power consumption, also it will reports every notification to all
devices in the association group.
For "Meter Supported Get" : the Z-Wave
3.
command with any of the following supported scales, and the ZL7261 will report back with the energy
consumption values for the requested scale:
Scale: 0x00-kWh
0x01-kVAh
0x02-W (Default)
0X04-V
0X05-A
0X06-Power Factor.
4.
Power Level Control:
* Use PowerLevel Set Command to set the RF strength during a specific period.
* Use PowerLevel Test Node Set Command to test the RF strength for specific node.
5.
Manually turn the connected appliance On/Off by your controller or pressing the Program Switch.
This is toggle switch. If the connected appliance is OFF, pressing the Program Switch turns the
connected appliance ON and vice versa.
6.
The on/off function uses the Z-Wave Switch Binary Command Class (or Basic Command Class) to
control its operation. Sending a switch binary set command with a level of 0 (0x00) will turn off the
device, and sending a level of 255 (0xFF) will turn on the device.
7.
Repeater Function: This device acts as a repeater for the Z-Wave mesh network functionality.
Plug Type B
0~5A
5~10A
10A~
Interface Controller into "inclusion" mode,
TM
TM
Interface Controller into
TM
Interface Controller or Gateway can send "Meter Get"
-3-
8. Configuration:
Parameter
Size
Auto report
1
1 byte
timing
Report when
2
2 byte
Watt change
9.
Support Meter Auto Report Function.
10. Overload Protection: If load is excess 15.5A for Type B plug or 10.5A for all others, then relay will
automatically cut off. To restore the relay, please power off & power on the device again.
11. Support SECURITY S0, SECURITY S2 UNAUTHENTICATED & SECURITY S2 AUTHENTICATED.
12. Support SmartStart, please scan the QR Code from ZL7261 for SmartStart. The Z-Wave SmartStart
QR code is located on the body of the ZL7261DE-5 and is immediately above the text identifying the
Z-Wave Pin Code. Also, the full DSK can be only found on the additional card in the package
13. Reset: Press the Program Switch then power on (plug-in) and hold for 5 seconds before release the
switch. Only use this procedure when the primary controller is lost or otherwise inoperable. (Remark:
This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)
14. Support OTA (Over-the Air) Firmware update from controller. Please refer to your controller manual.
Once OTA function success, please make sure to exclude the device & include again before using
the device.
Value
Notes
1 ~ 120 minutess
Report
(Default 1 minute )
kWh/kVAh
5-3600 watt for Type B plug
5~2300 watt for all other plug
Report V.A.W
(Default 50 watt)
-4-
Advertisement
