Related Manuals for EcoMotion CITY 2019
Summary of Contents for EcoMotion CITY 2019
- Page 1 USER MANUAL CITY Warning! In order to ensure your safety and to get the most out of your eBike, please read this user manual carefully before the first use. www.ecomotionbikes.com contact@ecomotionbikes.com © 2019 Ecomotion Bikes...
-
Page 2: Table Of Contents
Table of Contents: Warnings Definitions Assembly instructions Handlebar Headlight & Front fender Front wheel Saddle Pedals Brake - sets adjustment Handlebar adjustment Mounting & dismounting of battery Bike Inspection prior riding Turn power on / the display Display settings Display’s error symbols The battery &... -
Page 3: Warnings
Warning! Accidents and falls may cause severe injuries and in extreme cases even death! Read this user manual responsibly, with care and judiciousness! Also, always make sure that your e-bike is well assembled, Warning! well maintained, and in a good condition according to this When using your e-bike at the first - time, ride it in a controlled user manual prior to riding! ... - Page 4 Warning! Braking distance is influenced by the road / trail condition as well as weather condition, speed of riding & weight of rider. Warning! User must be aware to all traffic laws & regulations prior to using the product. Warning! Avoid Storing the battery in extreme hot / cold temperature. ...
- Page 5 Warning! DO NOT charge the battery without supervision! DO NOT charge the battery overnight while all people are sleeping in the house! Warning! This model is equipped with motor shut-off system which controlled by the brakes. Make sure that the system is well operating before each ride. ...
-
Page 6: Definitions
Definitions: • PAS - Pedal Assist Support - a sensor that is located on the bottom bracket, recognizes the pedals movement and operates the motor accordingly to the PAS level which set on the display . • TAG - Twist And Go - a throttle that located on the handlebar activate the motor while it twisted. -
Page 7: Headlight & Front Fender
• Adjust the handlebar so it will be aligned with the bike’s fork. Tight- up both of the stem's sides screws, and close back its lever. Warning! Make sure that the front fork turns easily sideways and not jammed while you steering the handlebar. -
Page 8: Front Wheel
3. Front wheel: • Unscrew the fork support rod from the bottom of the fork, and pull out the plastic spacer from the brake caliper. • Slide in the lock rod of the wheel into its place in the wheel’s hub and close it with its screw nut from the other side. ... -
Page 9: Saddle
4. Saddle: • Open the saddle's hoop that located on the bike's frame, slide-in the saddle into its place in the frame, and lock-back the hoop. Make sure that the saddle cannot turn to the sides or move up & down after you are locking it into the frame. ... -
Page 10: Brake-Sets Adjustment
Brake-sets adjustment Make sure that the brake pads are not rubbing or locking the front / rear disc, while you're not pressing the brake-levers. • In case in which the disc rubs / locked into the brake pads. Release a bit both of the caliper screws (the screws that connect the caliper to the fork), tightly press on the brake - lever and re-screw back the screws into their place while continuously pressing on the lever. -
Page 11: Handlebar Adjustment
Handlebar adjustment • Open the stem's lever, adjust the angle & hight of the handlebar to the desired position and lock it back into its place by re-closing the lever. Warning! After adjusting the handlebar height and before riding the bike, make sure that the handlebar is well-locked in its new position, by strongly pushing it down to the ground and turn it to the sides. -
Page 12: Bike Inspection Prior Riding
Bike inspection prior riding: • Check that the wheels are well connected to the frame / fork, and that they are rotated freely. • Check that the handlebar aligned with the front wheel, and all the screws are tight. • Check that there are no loose or missing spokes in the wheels. -
Page 13: Turn Power On / The Display
Turn power on / the display: • Turn on / off the battery by pressing on it power button. • Turn on / off the display power by long press on the button. (make sure that the battery is on before turning on the display). •... -
Page 14: Display Settings
order to leave the settings screen long press both & buttons. Display settings: P01: Screen backlight level (1-3) P02: 0 - Km/h 1- MPH P03: Battery Voltage (24V/36V/48V) P04: Sleeping time (minutes for display automatically shuts - off) P05: PAS levels in use (5 bars / 3 bars) P06: Wheel dimeter ... -
Page 15: The Battery & Charger
- Throttle failure - Motor failure The battery & charger: • Turn on / off the battery by pressing on it power button. • Turn on/ off the battery taillight by pressing on the light button. - Page 16 Warning! • Do not perforated or dropped the battery; • Do not placed the battery near to fire or another heat dispersing element; • Do not soaked the battery in water; • Do not placed / use the battery at the vicinity of strong electromagnetic or electrostatic fields;...
-
Page 17: Charging Of Battery
Charging of the battery: • Make sure that the battery is powered-off • Plug the charger to the outlet first and then plug it to the battery. • The charger red indicator light shows that the battery is in charging process. -
Page 18: Preserving Of Battery's Lifespan
Important! Batteries work better when they are fully charged. It is recommended to begin riding when battery is fully charged. Preserving of battery's lifespan: • make sure you charge the battery in full at least once in every 20 charging cycles •... -
Page 19: Tips For Proper Use
/ wet area. • Use only original parts. Do not use substitutes parts unless they permitted by Ecomotion Bike. please consult with us about substitutes parts at contact@ecomotionbikes.com. Using substitutes parts without consulting may void warranty. -
Page 20: More Info & Contact Us
• The Bike's brakes and their pads needs to be inspected in bicycle store on a regular basis. • Inspect the electrical wiring occasionally to make sure no wires torn or damaged, and that all connectors are well connected to each other. -
Page 21: Malfunctions & Solutions
Problem Possible cause Solution Inflate tiers to recommended Low tire air pressure pressure Brake pads rubbing against their discs Adjust brakes and / or caliper PAS magnets away from sensor Attached the magnets to the sensor Speed / range Low battery Charge the battery full charge reduce Battery lifetime is over / shortened... - Page 22 Problem Possible cause Solution Faulty PAS sensor Replace sensor and retest Faulty throttle Replace throttle and retest Motor runs without using TAG / PAS systems Replace main cord and Wire short throttle cord and retest Replace controller and Faulty controller retest Make sure that bake Motor shutdown system operated...
Need help?
Do you have a question about the CITY 2019 and is the answer not in the manual?
Questions and answers