Table of Contents
Advertisement
Quick Links
GridMaster
Microgrid Control System
®
Table of Contents
Section
Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Read this Instruction Sheet . . . . . . . . . . . . . . . . . . . 2
Retain this Instruction Sheet . . . . . . . . . . . . . . . . . . . 2
Proper Application . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operating Considerations . . . . . . . . . . . . . . . . . . . . . 2
Special Warranty Provisions . . . . . . . . . . . . . . . . . . . 3
Warranty Qualifications . . . . . . . . . . . . . . . . . . . . . . 3
Understanding Safety-Alert Messages . . . . . . . . . . . 4
Following Safety Instructions . . . . . . . . . . . . . . . . . . 4
Replacement Instructions and Labels . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . . 5
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
August 19, 2019
© S&C Electric Company 2019, all rights reserved
Rack Mounting Configuration
Installation
Page
Section
Installation
Before Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Option Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Final Setup and Checkout . . . . . . . . . . . . . . . . . . . .10
General Specifications . . . . . . . . . . . . . . . . . . . . . . .11
Module Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Instruction Sheet 1025-511
Page
Advertisement
Table of Contents
Summary of Contents for S&C IPERC GridMaster
-
Page 1: Table Of Contents
GridMaster Microgrid Control System Rack Mounting Configuration ® Installation Table of Contents Section Page Section Page Introduction Installation Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Before Starting . -
Page 2: Introduction
Introduction Qualified Persons WARNING Only qualified persons who are knowledgeable in the installation, operation, and maintenance of overhead and underground electric distribution equipment, along with all associated hazards, may install, operate, and maintain the equipment covered by this publication . A qualified person is someone who is trained and competent in: •... -
Page 3: Special Warranty Provisions
Introduction Special Warranty The standard warranty contained in the seller’s standard conditions of sale, as set forth in Price Sheet 150, applies to GridMaster Microgrid Control System, except that the first Provisions paragraph of said warranty is replaced by the following: (1) General: The seller warrants to the immediate purchaser or end user for a period of 10 years from the date of shipment that the equipment delivered will be of the kind and quality specified in the contract description and will be free of defects of... -
Page 4: Safety Information
Safety Information Understanding Several types of safety-alert messages may appear throughout this instruction sheet and on labels and tags attached to your S&C GridMaster Microgrid Control System. Safety-Alert Familiarize yourself with these messages and the importance of these signal words: Messages DANGER “DANGER”... -
Page 5: Safety Precautions
Safety Precautions DANGER The S&C GridMaster Microgrid Control System may be installed in equipment that operates at high voltage. Failure to observe the precautions below will result in serious personal injury or death. Some of these precautions may differ from your company’s operating procedures and rules . -
Page 6: Shipping And Handling
Shipping and Handling Inspection Packing Examine the shipment for external evidence of damage as A complete GridMaster Microgrid Control System consists soon after receipt as possible, preferably before removal of the following components: from the carrier’s conveyance. Check the bill of lading to •... -
Page 7: Before Starting
Installation Before Starting Familiarize yourself with the parts of the GridMaster controller. See Figure 1. Blank On/Off Power Terminal 1 Terminal 2 GPS Antenna Ethernet 0 Ethernet 1 Plate for Switch Options Figure 1. GridMaster controller: rear view. S&C Instruction Sheet 1025-511... -
Page 8: Installing The Rack-Mounted Gridmaster Controller
Installation Installing the Rack-Mounted GridMaster Controller Rack-mounted GridMaster controllers can be installed in a standard 1U slot in a 19-inch (483-mm) equipment rack. To install the GridMaster controller into an equipment rack: STEP 1. Use best practices for installing rack equipment by installing the heaviest equipment on the bottom of the rack. -
Page 9: Making The Control Power, Data, And Gps
Installation Making the Control Power, Data, and GPS Connections A GridMaster controller comes standard with connections for power, two Ethernet ports, a coaxial port for connecting a GPS antenna, and two screw terminal connectors. See Figure 1 on page 7. Make the control power, data, and GPS connections by completing the following steps: STEP 1. -
Page 10: Option Plate
Installation Option Plate A number of options, including digital Input/Output connectors, CAN ports, and analog Input/Output ports, can be custom-engineered and installed in place of the options plate depending on the application. Wiring information on the options will be provided as a part of the system diagram supplied with the GridMaster Microgrid Control System. -
Page 11: Appendix
Appendix General Specifications Control Voltage 24 Vdc Operating Temperature -20°C to 50°C (-4°F to 122°F) Operating Humidity 95% non-condensing humidity Altitude 3000 meters (9843 feet) Module Pinouts Terminal 1 and Terminal 2 24 Vdc Ethernet Function Data (TX +) Data (TX -) Data (RX +) Ground (-) Ground (-)
Need help?
Do you have a question about the IPERC GridMaster and is the answer not in the manual?
Questions and answers