Advertisement
Quick Links
Advertisement
Summary of Contents for Inerventions Mollii
- Page 1 User Manual Mollii Please read through the entire user manual prior to use.
- Page 2 User Manual (EN) ..................5 is user manual (version 1.55.2 EN) was produced by Inerventions and applies to Mollii. e operating instructions are valid from 2017-05-01. So ware version: 1.2x Inerventions AB, Svärdvägen 11D, SE-182 33 Danderyd. Tel: +46 (0)8 410 277 01...
- Page 4 ENGLISH...
- Page 5 Note that every size of jacket and trousers has a unique item number. For a complete list of item numbers see: www.inerventions.se Intended use Mollii is a personal assistive device. Electrically stimulating the muscles relaxes spastic, tense and aching muscles and activates weak musculature. Mollii is for use in the home environment.
- Page 6 Symbol: Patient connection is Symbol: Do not bleach. classi ed: BF. Symbol: Read the entire user Symbol: Do not wring out when manual prior to using Mollii. drying.
-
Page 7: Safety Instructions
e garment should ere is a risk of Mollii and is therefore at the consequently be turned disturbing the function user's own risk. Always off if it gets wet, and of the above-mentioned consult a doctor. -
Page 8: Skin Care
- Never insert objects or Mollii. Bear in mind that, tools under the garment. for example, the balance - Do not use Mollii if the can be aff ected. control unit has visible Do not undertake marks or is damaged. - Page 9 844 hPa (0 m to 2,000 m Use baby wipes for this Remove all batteries if above sea level). as they are gentle on the Mollii is not going to be skin. used for a period of 3 Keep the surrounding weeks or more.
-
Page 10: Connecting The Control Unit
BATTERIES DRESSING Use a crosshead screw- Always check that Mollii is Correct position: driver to undo the 4 intact and clean before use. screws on the rear of the control unit. Put on both parts of the garment (jacket and... - Page 11 Dressing 1. Start with the trousers. Ensure that the lower zip ends up on the outside of the leg and forms a line between the ankle and the outside of the knee. 2. Check that the zips on the trousers form a straight line on the outside of the leg in accordance with the pictures below.
- Page 12 4. Put the jacket on by inserting one arm at a time. Ensure that the side zips end up on the outside of the arm. 5. Check that the zips are positioned as in the picture on the le . 6.
-
Page 13: During Use
ON/OFF button. practise the movements that are hard to implement. Press “PLAY/PAUSE” BEAR IN MIND once. Mollii is intended to be used for approx. e display shows: 60 minutes every other day. Always follow Inerventions' instructions for safe use. - Page 14 • Maximum amplitude: 20 V. Each Mollii suit is customised when it is prescribed. Depending on diagnosis and manual examination of the patient, the prescriber decides which muscles are to be stimulated and with which pulse width. e user is not able to set pulse parameters or which muscles are to be stimulated.
- Page 15 Guidance and the manufacturer’s declaration – electromagnetic radiation Mollii is intended to be used in an electromagnetic environment as below. It is the customer’s and the user’s responsibility to ensure that usage is limited to the environ- ment described.
- Page 16 Guidance and the manufacturer’s certi cation – electromagnetic immunity Mollii is intended to be used in an electromagnetic environment as below. It is the customer’s and the user’s responsibility to ensure that usage is limited to the environment described. Immunity test...
- Page 17 A site investigation should be considered to evaluate the electromagnetic environ- ment on the basis of these factors. If the eld strength measured in locations where Mollii is going to be used exceeds the above RF values, use of Mollii should be monitored and regulated so that normal func- tion can be ensured.
- Page 18 Mollii is intended for use in an electromagnetic environment where disturbances and radia- tion from RF equipment can be checked. e customer and user of Mollii can prevent electro- magnetic interference by maintaining a minimum distance between portable and mobile RF communication equipment (transmitter) and Mollii according to the recommendations below.
- Page 19 Reporting faults and accidents Contact Inerventions AB immediately in the event of accidents or incidents. Use the contact details below: Inerventions AB Svärdvägen 11D 182 33 Danderyd Tel: +46 (0)8 410 277 01 Mail: support@inerventions.se If equipment is defective, contact Inerventions using the contact details above for return...
- Page 21 Inerventions AB, Svärdvägen 11D, SE-182 33 Danderyd. Tel: +46 (0)8 410 277 01...
Need help?
Do you have a question about the Mollii and is the answer not in the manual?
Questions and answers