Table of Contents
Advertisement
Quick Links
Tools Needed for Assembly
Stud finder (for wood stud wall)
Pencil Mark
Electric drill
Use a qualified professional to properly install. VideoSecu is not liable for the improper use or installation of
its products. Hardware provided is for mount through standard thickness drywall into wood studs, or mount to
solid concrete wall. Installers are responsible to provide hardware for other types of mounting situations.
For metal stud wall or other hollow wall installations, toggle bolt anchors can be purchased from your local
hardware store, consult a specialist at your local hardware store for select and use special anchors.
Wood Stud Wall Installation
Step 1. Locate the Wood Studs
Wall studs run vertically (up and down) inside the wall, behind the
drywall or plaster. The wall plate must be mounted to wood stud.
1-1. Using an awl, a thin nail, a small drill bit, or an edge to edge stud finder,
finds the edges of the stud.
1-2. Mark the centerline of the stud.
Step 2. Drill Pilot Holes
2-1. Hold the wall plate so the holes line up with the stud center lines.
2-2. Level the wall plate and mark the mounting hole position.
2-3. Drill a pilot hole at the marked location using a power drill
and a 5/32" drill bit.
Step 3. Mount Wall Bracket
Using the provided lag bolts, tighten
each bolt with a socket wrench. Do
not use power drill and do not over
tighten the lag bolts.
Visit our website at www.VideoSecu.com
Installation Instruction
Drill bit (for wood stud wall)
Masonry drill bit (for concrete wall)
Ratchet
Measuring tape
Phillips screwdriver
Level
drill bit diameter
5/32"
© 2016 VideoSecu.com
STUD
STUD
drill depth
2-1/4"
M6 Flat washer
ST6.3×65
Self-tap screw
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for VideoSecu ML531BEV3
- Page 1 Electric drill Ratchet Use a qualified professional to properly install. VideoSecu is not liable for the improper use or installation of its products. Hardware provided is for mount through standard thickness drywall into wood studs, or mount to solid concrete wall. Installers are responsible to provide hardware for other types of mounting situations.
- Page 2 Note: The flat washers are only used for M4 or M5 screw. FOR TV WITH CURVED BACK FOR TV WITH FLAT BACK Plastic sleeve Flat Flat washer washer M4~M8 Screw Back of the TV M4~M8 Screw Back of the TV Visit our website at www.VideoSecu.com © 2016 VideoSecu.com...
- Page 3 6-4. For TV with mounting hole pattern 300 x 200mm (11 13/16 x 7 7/8 inches), 400 x 200mm (15 3/4 x 7 7/8 inches) install the optional adapter kit as following. 400mm (15-3/4”) 300mm (11-13/16”) M6*6 Screw Visit our website at www.VideoSecu.com © 2016 VideoSecu.com...
- Page 4 TV plate, so you can adjust the adaptors align with TV screw mounting holes, put TV mounting screws into the TV mounting hole first, then tighten the adaptors. Loosen the screws Visit our website at www.VideoSecu.com © 2016 VideoSecu.com...
- Page 5 Tension is pre-set at the factory. Some time you may loosen arm adjustment bolts to adjust tension. 8-3. Tighten the bolts after moving the TV to desired location. +5° -15° ±5° Pivot: +5° -5° Tilt Angle: +5° -15° Visit our website at www.VideoSecu.com © 2016 VideoSecu.com...
- Page 6 Find the plastic concrete anchors(do not use it in wood stud wall). Place an anchor in each hole. Tap each anchor flush with the wall using a hammer. Plastic anchor M10 Flat washer M6 Self-tap screw ST6.3×65 Concrete wall Visit our website at www.VideoSecu.com © 2016 VideoSecu.com...
Need help?
Do you have a question about the ML531BEV3 and is the answer not in the manual?
Questions and answers
With the ML531BE2, once I have the TV level, how do I lock down the pivot? My cat tends to pivot it from the dresser right next to it.
After adjusting the TV level on the VideoSecu ML531BEV3 mount, lock the pivot by tightening the back nut.
This answer is automatically generated