Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Vauth-Sagel Flat move
- Page 1 Flat move Operating and assembly instructions Important document for the consumer...
-
Page 2: Table Of Contents
CONTENTS Page 1. GENERAL EXPLANATIONS 1.1 Introduction 1.2 Intended use 1.3 Safety information 2. EQUIPMENT 3. FEATURES 4. ASSEMBLY 5. ELECTRICAL CONNECTIONS 5.1 Establishing electrical connections 6. OPERATION 7. SYMBOLS USED 8. LABEL 9. TECHNICAL DATA 10. FAULT DIAGNOSIS/FAULT CORRECTION 10.1 Initialisation 11. -
Page 3: General Explanations
1. GENERAL EXPLANATIONS 1.1 Introduction This TV lift system has been constructed in accordance with the current valid German and European norms, regulations and guidelines and therefore corresponds with the generally approved technological rules at the time of delivery. 1.2 Intended Use The TV lift system may only be used for lifting and lowering flat screens with suitable fastening threads and the original system components in accordance with the operating and assembly instructions and is intended for installation in furniture. -
Page 4: Equipment
EQUIPMENT Pos. Components Comment Telescope drive Fixing screws 8 x Spax-Panhead 5 x 20 Control box Operating element Motor cable Mains cable Dependent on features TV switch-off Dependent on features Wireless receiver Dependent on features Wireless receiver cable Dependent on features Remote control Dependent on features Retainer plate... -
Page 5: Features
FEATURES The Vauth-Sagel TV lift system has been specially developed for lifting and lowering flat screens and has the following features: = Smooth and jerk-free accelerating and braking to preserve the flat screen = Anti-collision function – if the system collides with a solid object when moving, the drive stops and moves back approx. - Page 6 2. Screw the control box to an accessible point with 4 screws (8 to 10mm diameter) or fix it to the base. Consider the travel path of the TV when positioning the control box and the other components. The cables may not be bent or damaged. 3.
-
Page 7: Electrical Connections
ELECTRICAL CONNECTIONS Note: the mains plug should only be inserted when all other connections have been connected. The system may only be connected with the mains voltage stated in section 9. 5.1 Establishing the electrical connections 1. Connect the motor cable to the telescopic drive and insert the second end of the motor cable into the connection (1) of the control box (illustration 1). -
Page 8: Operation
TV switch-off connections Control box 2 (IN) Control box – mains connection (CB) Mains plug TV mains connection (TV) (With automatic switch-off) Additional unit – mains connection (AUX) (With automatic switch-off) Illustration 3 OPERATION For version with remote control: Before the system can be set with the remote control, the remote control and the wireless receiver must be aligned (wireless receiver stores the remote control’s identification code). -
Page 9: Symbols Used
The system must be set to the required drive out height once again by using the operating element. SYMBOLS USED LABEL Observe the danger information in the operating and Vauth-Sagel Systemtechnik GmbH & Co. assembly instructions D-33034 Brakel-Erkeln Neue Str. 27 Tel. 05272/601-01 Article/type: TV lift system... -
Page 10: Technical Data
TECHNICAL DATA Electrical Mains voltage 230 V ~ 50-60 Hz data Input power 400 W Output voltage 18 V Operating mode Int. max 10 %, max. 2 min/18 min Remote control frequency 433 MHz System data Installation height 847mm +5/-2mm (body construction with flap), 833mm +5/-2mm (body construction with lid) (standard-setting) Installation depth 195 mm (motor housing) -
Page 11: Cleaning And Maintenance
Sketches, diagrams and illustrative drawings are not to scale. Publisher: Vauth-Sagel Systemtechnik GmbH & Co. · Neue Straße 27 · D-33034 Brakel-Erkeln · Tel. +49 (0) 5272 601-01 · Fax +49 (0) 5272 601-193 Reproduction, including extracts, is only permitted with previous authorisation from the publisher...