Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DeVi-Stairlifts UP
Summary of Contents for DeVi-Stairlifts UP
- Page 1 UP stairlift installation manual V2.1 28-5-2019...
- Page 2 This UP stairlift is FOR INDOOR USE ONLY The warranty for the UP Stairlift void if the unit is installed or maintained by anyone other than an authorized UP dealer.
- Page 3 Design the rail Saw the rail to length Place the supports and rail as in the drawing Place the rack in the rail and grease it Place the stairlift Configure the stairlift with the app mount the endcaps onto the rail Controll the functions Explain the functions to the customer Fill in the form...
- Page 4 Rail mounting Installing the charging stations Installing the carriage Safety Checks Control check Remote control check Safety sensors check Limit check Seat swivel check Footrest check Check for smooth travel Labelling Demonstrate UP stairlift to the User Maintenance Avoiding unsafe installation...
-
Page 5: Health And Safety Hazards
Health and safety hazards The risk of falling down the stairs The risk of body parts or loose clothing getting trapped The risk of direct and indirect electrical contact The risk of injuries caused by inappropriate use of tools The risk of tools falling down the stairs Use of necessary protection (safety glasses etc) Never use worn tools The risk of tripping hazards on the staircase... -
Page 6: Box Content
• Check the carton contents for shipping damage as soon as the box arrives. • Verify the contents against the packing list BEFORE leaving the shop for the installation site. • Report any discrepancies to DeVi-Stairlifts immediately. • Damage claims must be reported within 5 days. • complete carriage with seat •... -
Page 7: Installation Tools
Installation tools Always check if you have all necessary parts and tools before travelling to the installation site. • power drill + segments for drill bits • drill bits: appropriate for oor (eg. concrete, hardwood, tiles) • crosshead bit for power drill type •... -
Page 8: Pre-Installation Procedure
pre-Installation procedure Before starting the installation of the stairlift perform the following preparations and checks: 1. Visually inspect the plastic covers. Check for damages that might have occurred during transport. In case of any damages do not install the lift and contact an authorized dealer. 2. -
Page 9: Installation
Installation Measuring the rail. install-drawing-1-f12bd63ad3 Download the manual ‘UP webshop manual’ from www.upwebshop.com. Go to the part webshop, login, click on Downloads and there you can find the manual. Or click HERE if you are reading this manual digital. Then follow the steps for measuring the stairs as described. When filling in these measurements the tool will provide you with a drawing. -
Page 10: Installing The Rail
Installing the rail The rail is built up from the different segments. The following steps explain how to connect the different segments and mount the rail to the stairs. Connecting different segments 1. Start by sawing the straight parts to the desired length as measured before ordering the stairlift. - Page 11 4. Complete the curve by adding segments (AB070000) until the desired turn angle is reached. Every segment is 5°. Remember that two segments of the turn are already in place. At the red arrows a DIN 912 M6X30 screw should be placed with a DIN 934 M6 nut, with the help of a fixing torque.
- Page 12 3. Slide a nut M8 ISO 4017 in both of the two slots pointed out by the blue arrow in figure 11. (fig. 11) 4. Fix the mounts by a bolt M8x16 DIN 934 through the last hole of a mount and the nuts M8 ISO 4017 placed in step 3. See figure 12, for the holes to put the bolts through.
- Page 13 Installing the charging stations 1. Put two ferrules on the black and red wires with the connector for the charger (fig. 15). (fig. 15) 2. Measure the length that is necessary to connect two charging stations plus 20 cm extra and cut a red and black wire on this length. Put ferrules on either end.
- Page 14 5. You have to place the charging stations approximately at the beginning and the end of the rail and at points that is handy for the customer. To place the charging station on the rail, you have to shove two nuts M8 ISO 4017 in the back slot at each straight part of the rail.
- Page 15 Installing the carriage 1. The carriage is delivered fully assembled on a piece of rail with short rail supports to level it. Grease the geat rack before usage. To get it out the box, remove all other parts from the box and remove the bolts from the rail support. Get the carriage out of the box including the rail part.
- Page 16 (fig. 23)
- Page 17 The password is 1234. Open the app on your phone. Push the button “Connect”. Push the button QR and scan the QR-code that is on the right side of the UP. Now your phone is ready to use as a remote for the stairlift.
- Page 18 This is done with four DIN 7500-1 M6X20 bolts through the four holes of the end plate. (fig. 30) 13. Configurate the stairlift using the UP conigurate app. 14. The final step is to mount te QR code, or the optional remote controls, on the wall.
-
Page 19: Safety Checks
The stairlift should travel down. When releasing the button the stairlift should stop. 2. Press the upward button on the app or on the optional remote. The stairlift should travel up. When releasing the button the stairlift should stop. Safety sensors check 1. - Page 20 2. Push the armrest down. The footrest should go up. Check for smooth travel Drive the stairlift up and down the rails, ensure that the ride is smooth and stable. Furthermore check if the stairlift stops in the desired positions.
- Page 21 Demonstrate UP Stairlift to the user Have the user manual by hand for clear explanation. Explain to the user the correct operation of the stairlift, the procedures in case of a problem, the position of the alarm signal and the safety features implemented on the stairlift.
Need help?
Do you have a question about the UP and is the answer not in the manual?
Questions and answers