Advertisement
Quick Links
A S S E M B LY I N S T R U C T I O N S
Majestic Mailbox Kit with Planter Box
*
* Mailbox and mounting hardware for
the mailbox not included
Please read through before starting assembly.
Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 877 234 6196 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Post Cap (5)
2. Mailbox Post (1) - 3" x 3" x 54"
3. Post Arm (1) - 4" x 4" x 23"
4. Board Wall - Rear (2) 7/8" x 11" x 6 1/2"
5. Board Wall - Sides (2) 7/8" x 11" x 14"
6. Board Wall - Front (1) 7/8" x 11" x 14"
7. Planter Box Post (4) 3" x 3" x 12 1/4"
8. Planter Box Brace (1) 7/8" x 1 1/2" x 14 3/4"
9. Anchor Pipe (1) 36 5/8" Long
10. 5/8" Tek Screw (2)
11. 3" Self-Augering Stainless Steel Screw (4)
12. 1/4" Hardened Steel Drill Bit (1)
Tools You Will Need
• Cordless Drill
• Level
• Sledge Hammer
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5'x 8' for unobstructed assembling.
• You should not need to use excessive force when assembling components.
19 in
18 in
10
11
12
Not to Scale
7
6
Zippity
DO-IT-YOURSELF
FRIENDLY PRODUCTS
2 1/4 in
Ground
18 in
1
2
3
4
8
5
Ver 1.1/110617
9
1
Advertisement
Summary of Contents for Zippity Majestic Mailbox Kit with Planter Box
- Page 1 A S S E M B LY I N S T R U C T I O N S Majestic Mailbox Kit with Planter Box Zippity DO-IT-YOURSELF FRIENDLY PRODUCTS 2 1/4 in 19 in Ground * Mailbox and mounting hardware for...
- Page 2 Slide two planter box posts down over on each end of the front board wall. Zippity DO-IT-YOURSELF FRIENDLY PRODUCTS M a j e s t i c M a i l b o x K i t w i t h P l a n t e r B o x I n s t r u c t i o n s...
- Page 3 S T E P O N E ( CO N T ’ D ) Zippity Slide the two side boards down into place as shown. DO-IT-YOURSELF FRIENDLY PRODUCTS slide the last two posts into place over the boards as shown.
- Page 4 S T E P T W O Install Pipe Zippity DO-IT-YOURSELF FRIENDLY PRODUCTS Locate where you would like the mailbox post to go and using a sledge hammer, drive the pipe into the ground approximately 18” (18 5/8“ above ground).
- Page 5 S T E P T H R E E Zippity With the drill bit provided, pre-drill two holes through the vinyl DO-IT-YOURSELF post and metal anchor pipe as shown. The holes should be FRIENDLY PRODUCTS approximately 4” and 16” above ground and centered on the groove of the mailbox post.
- Page 6 Pressure fit the post caps into place as shown. You can secure caps on more permanently using PVC glue if necessary. Zippity DO-IT-YOURSELF FRIENDLY PRODUCTS Congratulations, you are finished! Please follow mailbox manufacturer’s instructions for installation of mailbox (not included) and mailbox mounting plate to the mailbox arm.