Table of Contents
Advertisement
Quick Links
BEFORE YOU BEGIN
BEFORE YOU BEGIN
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
·
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
·
These instructions contain important care, cleaning, and
warranty information -
consumer
.
ROUGHING-IN
A. Specifications
Activated by an infared sensor. The
Activation
machine operates automatically.
Dime sions
n
305 225 206mm
W H D
(12.0
Voltage/Power
220-240V, 50/60Hz, 2400~2800W
30 4cm for A4 white paper
Detection Distance
65
Air Temperature
temperature 25
60
Operation Duration
automatic shutoff)
Motor Type
Induction Type (Brushless)
AC 220V 50Hz 14m/s 10%
Air Velocity
AC 220V 60Hz 17m/s 10%
·
This machine is equipped with an infrared sensor for
automatic activation.
·
The product is made in Taiwan.
WARNING: Risk of electrical shock.
electrician should make all electrical connections.
WARNING: Risk of electrical shock.
a circuit protected by a Ground-Fault Circuit-
Interrupter (GFCI) or Earth-Leakage Circuit-Breaker
(ELCB).
WARNING: Risk of electrical shock.
power before servicing.
1045760-T01-D
please leave instructions for the
"
8.9
" 8.1"
)
o
o
o
o
C
to 75
C
(149 F to 167 F) Ambient
o
o
C
(77 F)
sec
(Self-protection
A licensed
Connect only to
Disconnect
·
·
·
A.
W H D
/
·
·
GFCI
106 2
324
528137
ã
-1-
ã
BARDON
BARDON
TOUCH
LE
SS HAND DRYER
Installation INSTRUCTIONS
305 225 206mm
(12.0
"
8.9
" 8.1"
)
220-240V, 50/60Hz, 2400~2800W
30 4cm
o
o
o
65~75
C
(149 F~167 F)
o
o
25
C
(77 F)
60
(
AC 220V 50Hz 14m/s 10%
AC 220V 60Hz 17m/s 10%
ELCB
200131
Copyright Kohler China Ltd., 2010
K-5486T
-
)
, 2010
Advertisement
Table of Contents
Related Manuals for Kohler BARDON K-5486T
Summary of Contents for Kohler BARDON K-5486T
- Page 1 · · All information in these instructions is based upon the latest product information available at the time of publication. Kohler China reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. ·...
- Page 2 B. Packing List Installation Kit Illustration Description Quantity Wrench Plastic Dowel Fixing Screw 1047977 Washer Power Board Assembly Spring Washer 1047946 Heater Assembly 1047945 Sensor Assembly 1047920-* Casing Casing-CP 1047920-CP Security Wrench Casing-OP 1047920-OP Casing-SH 1047920-SH Sensor assembly 1047945 Security Screw Heater assembly 1047946 Power board assembly...
- Page 3 STANDARD INSTALLATION STANDARD INSTALLATION Operation Diagram Sensor Detective Relay Neutral Heater Motor Live Neutral BEFORE INSTALLATION BEFORE INSTALLATION NOTE 60cm 1. Make sure the sensor is located min 60cm(23 inch) above everthing bellow to prevent false triggers. 2. Never install hand dryer onto a wooden or plastic wall finish.
- Page 4 INSTALLATION A. Installation Steps 1. Paste the installation template at appropriate location on the wall. 2. Drill four holes, dia 10mm insert plastic dowels. (Fig.1) 10mm ( 1) 10mm Fig.1 3. Insert screws into dowels and tighten them. (Fig.2) ( 2) Fig.2 4.
- Page 5 B. Installation Check 1. Check AC power cable connection. 2. Check if AC power on. 3. Put outer cover back. 4. Insert security screws and tighten them.(Fig.4) Fig.4 ( 4) C. Operation Instructions 1. The machine starts operating automatically when user s 20cm hands are put approximately 20cm (7.78") below the sensor located next to air louver.
- Page 6 D. Adjustment of Sensor 1. Loosen Secuity Screws and remove Casing. (Use the Security Wrench from the attached package in the carton.) 2. Refer to drawing for the location of power board. 3. Use a tiny flat screwdriver to turn adjustment screw in clockwise direction to lengthen the sensing distance.
- Page 7 Motor s condenser out of order. Notice: Troubleshooting needs to be done by professional of KOHLER CHINA. Users are not suggested to do this without help. Please remember that the checking and repairs done by users themselves could easily cause damage to the machine or cause physical harm to the person.
Need help?
Do you have a question about the BARDON K-5486T and is the answer not in the manual?
Questions and answers