Advertisement
Installation instructions
• This device must be located in a ventilated place to avoid the risk of water spatter.
• Do not install on heat-sensitive supports as carpet, PVC floor, etc...
• Imperatively install the product in a cool and dry place.
Wiring diagram
S4
S3
S2
S1
Pairing
• A long press (1.5sec) on the L key takes you into the set-up mode.
• Output 1 (S1) flashes, briefly press the switch button you want to turn
output 1 ON, then press a second time the switch button you want to
turn output 1 OFF.
Case 1 : ON/OFF with 2 buttons
Case 2 : ON/OFF with 1 button
ON
OFF
• Each press on the L key changes the activated output. The seventh press exits the set-up mode.
• If no action is taken for 2 minutes, the module returns to normal mode.
EXAMPLE : ALLOCATION OF A SWITCH TO OUTPUT 2
• A long press on the L key : output 1 (S1) flashes
• A second press of the L key : output 2 (S2) flashes
• Briefly press the switch you want to turn output 2 ON : output 2 is ON
• Briefly press the switch you want to turn output 2 OFF : output 2 flashes again
An ON switch and an OFF switch are now allocated to output 2. You can continue to
allocate more switches to the same output by pressing them or you can move on to
setting up output 3 (S3) by pressing the L key.
SCHEIBER
Bellevue, 85120 Saint-Pierre du Chemin
Tél : +33 (0)2 51 51 73 21
2.4 Ghz
S5
S6
Fuse 10-20A
8-32V DC Battery
Up to 16A, you can only use one output (1-2 or 3-4).
Beyond, the power supply must be doubled (1 to 4).
L key (learn)
To get into set-up mode and
change the activated output
ON/OFF
•
France
•
clients@scheiber.fr
120 Ω terminaison
CAN cable
120 Ω terminaison
CAN cable
S4
S3
S2
S1
NOTE: 2.4 Ghz antenna module has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference's by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
According §15.21 of the CFR 47- FCC part 15:
Any changes or modifications to this equipment not expressly approved by the responsible party may cause, harmful interference and
void the FCC authorization to operate this equipment.
•
sav@scheiber.fr
•
www.scheiber.fr
Markings used
Symbols
V
A
Kg
DC or
S4
S3
S2
S1
DC
AC
230V AC 8-32V DC power supply
C key (clear)
To clear a set-up output or the 6 outputs
of this lighting control module
• In set-up mode, (one of the module's outputs
flashes), a long press on the C key clears the
setup of the selected flashing output.
S5
• In normal mode, a long press (1.5 seconds) on
S6
the C key clears the set-up of all the outputs of
this module.
Note: It is also possible to remove one switch from
an output (without clearing the other switches
associated with that output). To do this, select the
applicable output with the L key on the module.
Then, when the output flashes, press the switch
you want to remove until the output starts flashing
again after having been off for 1 or 2 seconds.
Marinebeam LED Lighting
660 Riverland Dr, Ste B
Charleston, SC 29412
(843) 885-8644
Description
Volt
Ampere
Kilogram
Direct current
2.4 Ghz
S5
S6
Advertisement
