Subscribe to Our Youtube Channel
Summary of Contents for ThermoPro NP17-12 Pro
- Page 1 MULTIFUNCTIONAL DIGITAL BOTTOM PRE-HEATING AND SOLDERING SYSTEMS FOR PRINTED CIRCUIT BOARDS MANAUL FOR SAFITY AND USE English Edition 10E Helsinki 2015...
-
Page 2: Table Of Contents
TABLE OF CONTENT 1. Introduction ............................. 3 1.1. Documents take into account at production and in documentation ............. 3 1.2. Briefly about the Manufacturer ......................3 2. Safety measures working with System ...................... 4 2.1. Precautions and safety when using the equipment................4 3. -
Page 3: Introduction
1. Introduction We are grateful for your decision to purchase Digital Bottom Pre-Heating and Soldering System of NP Series for circuit boards. It was fabricated by us especially for you in accordance with the highest quality standards, and tested by our experts on compliance with EU directives shown in the section "Documents taken into account in production and documentation"... -
Page 4: Safety Measures Working With System
2. Safety measures working with System WARNING! Read all instructions and safety recommendations. Failure to fill the instructions and recommendations may lead to electric shock, burns, fire and / or serious injury. Keep these instructions with recommendations for future use. Digital Bottom Pre-Heating and Soldering System of NP Series is designed for installation and remove of electronic components. -
Page 5: The Device Description
Improper use of tools or failure to follow the safety rules stated in this Manual may cause serious personal injury. 3. The device description 3.1. Technical characteristics of NP Series pre-heating systems PARAMETERS NP17-12 Pro NP24-17 Pro NP34-24 Pro Power Voltage [V] ~220V – 50Hz... -
Page 6: Digital Bottom Pre-Heating And Soldering System Of Np Series Delivery Specification And Its Application
Digital Temperature Controller Temperature control Sensor DATA cable RS-232C (9x9pin) “ThermoPro-Center” software on CD Manual for Safety and USE System Modifications differ with Wattage and sizes of working plates. NP17-12Pro, NP24-17Pro devices are heating and soldering by thermo-profile controlled by device TP1-10KD Pro. Double hearing zone unit NP34-24Pro is recommended for big size PCB processing. - Page 7 Temperature Controller TP2-10AB has two independent channels (A&B) for temperature regulation at connected loads. These can be pre-heaters NP17-12 Pro, NP24-17 Pro or one of NP34-24 Pro plates (zones). For simultaneous control of two loads TP2-10 AB controller has a virtual channel “AB”.
-
Page 8: Technical Characteristics Of Tp Series Temperature Controllers
Digital Temperature Controllers Features: Heating turn on/off with dedicated button; Quick setting up of temperature of stabilization; Quick select of temperature of stabilization from a memory; Simultaneous display of operation temperature sittings and real heather temperature, and control sensor temperature as well;... -
Page 9: Before Working Start
Power Cord; Thermo-sensor; Data cableRS-232C (9x9pin) Software “ThermoPro-Center “on CD; Manual for Safety and Use in original; If any of above components missed or damaged please address this fact to your Supplier. 4.2. First Switch On First of all read the Present Manual in full. -
Page 10: Equipment Operation
# appear one after other on display, after what device turns into autonomic mode and heating is on. While the Controller runs the “ThermoPro-Center” program has to be loaded and opened after the controller turned on. This consequence caused by the fact that the Program makes a search of devices connected to Computer before its start. - Page 11 Pic.2.1. Back panel of device TP1-10KD Pro 1- Power Cord 2- Rack of fuses 3- Terminal for Load connection (thermo-plate) 4- Terminal for control thermo-sensor connection 5- RS-232C Connector Pic.2.2. Back panel of Connector TP1-10KD 1- Power Cord 2- Rack of fuses 3- Terminal for Load connection (thermo-plate) 4- Terminal for control thermo-sensor connection Pic.2.3.
- Page 12 Pic.2.4. Back panel of device TP2-10AB 1- Power Cord 2- Rack of fuses 3- Terminal for Load connection Front panel of the Controller contains elements of control and indication. Pic2.5. Control panel of Controller TP1-10KD Pro 1- Pre-heater plate ON/OFF; 2- Button for reducing temperature of stabilization;...
-
Page 13: System's Work In Autonomous Mode
Pic.2.7.Control Panel of TP1-10KD, TP1-10 1- Pre-heater plate ON/OFF; 2- Button for reducing temperature of stabilization; 3- Button for increasing temperature of stabilization; 4- Memory buttons; 5- Heater ON Power indicator 6- Zone of display for Channel name and temperature of stabilization setting. If the heater is OFF the “Off”... -
Page 14: Selection Of Heating Channel Ob Controller Tp2 -10Ab
The controller has two independent channels of temperature control - A and B, which connect two pre- heaters NP17-12 Pro, NP24-17 Pro or NP34-24Pro having two independent heating plates (zones). After selecting a channel the change temperature of stabilization at channel can be done, as well as turn on /off the heating at the channel. -
Page 15: Heater Turn On And Off
temperature change or inscriptions "O.C." and "S.C." can appear in the temperature of stabilization display zone. For system recovery turn off the power for 20 seconds, then press and holding the button to increase the temperature stabilization turn the power temperature controller on. After the display lit on release the button. -
Page 16: Thermograph Read Out (For Controllers Tp Х-Хkd Pro)
A control sensor for temperature measurement is installed on a object during a process run. The value of the temperature on sensor will be presented on the Controllers display, as well as on Virtual Panel of Devices in a “ThermoPro-Center” Program interface. Do not install the sensor on the radio elements and other objects ATTENTION! that are energized, without additional isolation. - Page 17 The program corrects the temperature automatically in a way to match profile as closer as possible. The full methodic for Program setting for soldering by profile is presented in the “ThermoPro- Center” Manual.
-
Page 18: Maintanece
Pic.4. At the point of solder reflow completion (point A) the AirCooler automatically switches on, and a PCB cooling zone is formed. The cooling rate is defined by thermo- profile. After the board surface is cooled to a temperature 130-140 ° C, the product can be removed from the heating-plate. The Cooler speed is switched to maximum for a quick cooling of the working surface (to a temperature of 50-60 °... - Page 19 • Checking for grounding power in socket; • Checking the grounding at the system "temperature controller - thermo-plate"; • Clean the housing and display of the Controller with a soft cloth. Not recommended for cleaning use solvents or alcohol-containing liquids; •...
-
Page 20: Storage And Transportation Requirements
or temperature value outside parameters of the Controller. Or button of temperature setting un of working limits. the same failure took place in a pressed. The same problem upon process of recording. Check a voltage in Power supply line, temperature recall from take measure for protection from memory. -
Page 21: Disposal
available, the defective product will be replaced with the same product or a similar type, if a defect in material or workmanship is found within the limited warranty period. The warranty period starts from the date of first customer purchase. Evidence of the date of purchase is a waybill or transport company consignment note with date delivery to the first customer. - Page 22 Deisgn and production of all “ThermoPro” devices, “ThermoPro-Center” Software and all rights to this brand owner is OOO NTF “Techno-Alliance Electronics” Russian Federation 113570, Moscow, Ulitsa Krasnogo Mayaka, 13, k4 Tel: +7 (495) 231-37-21 http://www.termopro.ru, E-Mail: ta@termopro.ru Edition 10E от 10.12.2015 The program Developers and Writerts: V.
Need help?
Do you have a question about the NP17-12 Pro and is the answer not in the manual?
Questions and answers