Page 3
OPERATING AND MAINTENANCE MANUAL MAX / MAX T CE Declaration of Conformity CE Declaration of Conformity UNIA Sp. z o.o. st. Szosa Torunska 32/38 86 – 300 Grudziadz, Poland Herewith declare with full responsibility that our product: cultivating unit MAX / MAX T type / model : …………………………………….
Page 5
OPERATING AND MAINTENANCE MANUAL MAX / MAX T UNIA Sp. z o.o. st. Szosa Torunska 32/38 PL 86 – 300 Grudziadz tel. + 48 56 451 05 00 fax. + 48 56 451 05 01 Service tel. + 48 56 451 05 26 uniamachines.com...
OPERATING AND MAINTENANCE MANUAL MAX / MAX T Table of contents PREFACE: ..............................5 1. Precautions ............................5 1.1 Before you Begin to Use Your Machine ..................5 1.2 Health and safety regulations ....................... 5 1.3 Servicing ............................6 1.4 Transport on highways ........................6 1.5 Safety symbols ..........................
OPERATING AND MAINTENANCE MANUAL MAX / MAX T PREFACE: When buying the machine, check completeness of its accessories that include the following components: • Operating Manual • Warranty Card Precautions 1.1 Before you Begin to Use Your Machine Read the instruction manual. •...
OPERATING AND MAINTENANCE MANUAL MAX / MAX T of the machine. It is too late for this after you start work! • Avoid wearing any loose clothing, which could be caught by rotating components of the machine. • Always keep the machine clean in order to avoid fire! •...
OPERATING AND MAINTENANCE MANUAL MAX / MAX T • The machine, as the part of the vehicle that protrudes outside the rear side outline of the tractor covering the rear lamps of the tractor, poses a threat for other vehicles in the traffic. •...
Page 10
OPERATING AND MAINTENANCE MANUAL MAX / MAX T Lubricate the machine on regular basis ACCORDING TO THE ROAD SAFETY REGULATIONS (REGULATION OF THE MINISTER OF INFRASTRUCTURE OF 31/12/2002 - JOURNAL OF LAWS NO. 32 OF 2002, ITEM 262), DRIVE ON HIGHWAYS ONLY AFTER HAVING OBTAINED AUTHORIZATION FROM THE COMPETENT HIGHWAYS ADMINISTRATION BODY WHERE THE JOURNEY BEGINS.
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 2. Technical and Identification Data MAX / MAX T – MAX tine unit and MAX T disc unit are designed for loosening and levelling the soil. Each section is provided with a ground-following system, so it perfectly adapts to the ground, on which it works.
Page 13
OPERATING AND MAINTENANCE MANUAL MAX / MAX T Fig. 2. Construction of MAX Fig. 3. Construction of MAX T Frame Rear roller Skid Deflector (option) Tine section Front roller or front skid Support Disc section Chassis with drawbar (option) - 11 -...
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 2.1 MAX Specifications Table 4. Machine type Item Parameter Machine type mounted mounted mounted/ mounted/ mounted mounted/ semi-mounted semi-mounted semi-mounted Working width No. of tines Max working up to 8 depth up to 8 up to 8 Tine pitch Roller type...
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 2.2 MAX T Specifications Table 5. Machine type Item Parameter MAX T MAX T MAX T MAX T MAX T MAX T Machine type mounted mounted mounted/ mounted/ mounted mounted/ semi-mounted semi-mounted semi-mounted Working width No.
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 3. Operating Manual 3.1 First Start Before the first start of the machine: Read the Operating Manual thoroughly, • • Check the technical condition of the unit, and, above all, the condition of its working parts, mechanisms protecting tines against overloading and the hydraulic system.
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 3.3 Mounting and Disconnection of Machines 3.3.1 Mounted Machines The tractor should stand on a hard and plain surface in order to connect the machine to it in a correct and safe way. Fig.
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 3.3.2 Semi-Mounted Machines (Chassis with Drawbar) The tractor should stand on a hard and flat surface in order to connect the machine to the tractor in a correct and safe way. Fig. 7. Connection of the semi-mounted machine a) Mounting •...
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 3.4 Access to the Field – Transport Fig. 8. Transport – MAX / MAX T – folding Fig. 9. Transport – MAX / MAX T- securing the machine Width of the machine can exceed 3.0m depending on the accessories, •...
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 3.5 Adjustment of the Cultivating unit 3.5.1. Working Depth Adjustment The adjustment of the working depth of both the tine and disc sections in the MAX and MAX T units is the same and is carried out by means of the bolts [A].
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 3.5.4. Unfolding/Folding the Outermost Disc of MAX T Fig. 13. Outermost disc unfolded Fig. 14. Outermost disc folded remove the cotter pin form the bolt [A] • • fold the extension with the coulter disc to its transport position insert the bolt [A] as in Fig.
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 3.5.6. Levelling the Machine Sections In order to obtain the correct position of all sections relative to the ground, adjust the right and left frames with the bolt [A]. To make adjustment, loosen the nut [B] and screw in/unscrew the bolt [A], adjusting the appropriate position;...
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 4. Operation Before beginning the field work with the machine: • disassemble the warning signs (together with the screwed brackets) for transport on highways, switch the hydraulic system to the position or mixed control mode. •...
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 5.4 Lighting check the correct connection of the 7-pin plug outputs before the first start, • check the lighting, plug, wiring and lamps every day, • • check cleanliness of the reflector plates. 5.5 Bolt, screw and nut tightening torques (Nm) Table 6.
OPERATING AND MAINTENANCE MANUAL MAX / MAX T 5.6 Lubrication Use mineral oils for lubrication. Clean the lubrication points before lubricant injection. Lubricate at the marked points (table no. 7). If the machine worked less number of hectares, please lubricate it before starting work and after its completion, and at all lubrication points.
Agricultural machinery is warranted to the provisions specified in the Instruction Manual for proper operation and maintenance. Under the warranty period, only the genuine parts made by ‘UNIA’ Grudziądz may be used. Any modifications or repairs made by the user are not allowed in the warranty period. This may lead to loss of warranty.
Page 27
OPERATING AND MAINTENANCE MANUAL MAX / MAX T COMMENTS AND NOTE …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… ……………………………………………………………….…………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………………….…………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… ………………………………….………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… ………………………………………………………………………………………………….………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …….……………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… - 25 -...
Page 28
OPERATING AND MAINTENANCE MANUAL MAX / MAX T COMMENTS AND NOTE …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………….……………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………………………………… ………………………………………………………………………………………………………………………………………………………….. - 26 -...
Page 29
OPERATING AND MAINTENANCE MANUAL MAX / MAX T U N I A Sp. z o.o. st. Szosa Torunska 32/38, 86-300 Grudziadz QUESTIONNAIRE Please read the entire questionnaire and write a short answer: 1. Machine ……..…………………………………………………………. serial number …………………………………………………………..………….. received on……………………………..……………………………………………………………………………………………………………………………… 2.