1. Manuals
  2. Brands
  3. Starburst Technologies Manuals
  4. Computer Hardware
  5. SB-HDQP-2130
  6. Instruction manual

Starburst Technologies SB-HDQP-2130 Instruction Manual

8vsb / atsc to qam processor
Hide thumbs Also See for SB-HDQP-2130:
Table of Contents

Advertisement

Quick Links

Download this manual
8VSB / ATSC to QAM Processor
SB-HDQP-2130
INSTRUCTION MANUAL
The content and design of this document is the intellectual property of PDI Communications, Inc. and is protected
Under copyright law. Any duplication of this material without written consent of an authorized officer of this company
Will be litigated to the fullest extent of the law.
®
Starburst
Technologies Customer Support
•
1-800-242-1606 ext. 274
1
Rev 2a

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SB-HDQP-2130 and is the answer not in the manual?

Questions and answers

Related Manuals for Starburst Technologies SB-HDQP-2130

Summary of Contents for Starburst Technologies SB-HDQP-2130

  • Page 1 8VSB / ATSC to QAM Processor SB-HDQP-2130 INSTRUCTION MANUAL The content and design of this document is the intellectual property of PDI Communications, Inc. and is protected Under copyright law. Any duplication of this material without written consent of an authorized officer of this company Will be litigated to the fullest extent of the law.

  • Page 2: Safety Instruction

    INTRODUCTION Mounting Ensure the unit is rack mounted securely on the wall or in the Thank you for buying the SDQM-2130 MPEG-2 SD Encoder 19’’ cabinet as not to cause harm to anyone or to damage Modulator Combo. Please read this manual carefully before the product by being dislodged.

  • Page 3: Specifications

    SPECIFICATIONS Input Channel RF Output Combinations: 2×ATSC / 2×QAM / 1×ATSC + 1×QAM RF carriers: Channel range: 2-134 Input QAM Frequency range: 64QAM / 256QAM Channel range: 2-134 Data rate: 26.9Mbps (64QAM), 38.8Mbps Frequency range: 54-860MHz QAM mode: 64QAM / 256QAM Data Rate: 26.9Mbps (64QAM), 38.8Mbps Input Level:...
  • Page 4 MANUAL OPERATION / SYSTEM LED FUNCTION Output Settings Via Push Button Enter the menu manually. OUP should appear. (Continue to next step) Press OK button to enter (FCY) mode. Press OK button to enter or verify channel number on the display, Press OK button again to access blinking Channel L.E.D.'s, Use the UP or DOWN buttons to change or set the Output Channel Number while the L.E.D.'s are blinking, Press OK to stop the blinking L.E.D.'s and confirm output channel number selection.
  • Page 5 IP Setup Via Push Button HCP = DHCP IP Setup Via Push Button NO HCP = STATIC Enter menu manually. OUP appears. Press up arrow twice for 1PA. Then OK button to enter HCP. HCP = DHCP mode, Press OK to see status of yes or no, Press Ok again to put into blinking L.E.D. YES HCP mode.
  • Page 6 Input Channel Set Up Via push button Enter the menu manually. OUP should appear. Next, press the DOWN arrow one time to enter CH1 mode, or press DOWN arrow two times to enter CH2 mode. “Ch1 and CH2 are Inputs.” CH1 or The display shows CH1 or CH2 depending upon which input port you have chosen to setup.
  • Page 7 ® Starburst Technologies Customer Support • 1-800-242-1606 ext. 274...
  • Page 8 Web Interface/ Remote Operation NOTE: The Factory Default Setting is DHCP To change this setting to STATIC, use front panel push buttons. (Refer to pg. #5) 1- Decide weather your connection will be STEP STATIC or DHCP and make the connection acording to diagram ( NOTE: A switch is required in order to use DHCP }...

  • Page 9: System Login

    The web browser allows the user to fully configure the SB-HDQP unit via an Ethernet connection and a web browser. A. Connect the PC to the LAN port of the SB-HDQP-2130 unit. B. The configuration process must be made acording to instructions on page 8 of this manual.

  • Page 10: System Parameters

    Stream Parameters User can edit the Swap VCN (Virtual Channel Name) in ‘Stream Parameters’. Note: Some TV models might required a complete channel re-scan in order to see the change. System Parameters User can reset the system or retrieve inventory. The “Set Password”...
  • Page 11 APPENDIX A – U.S.A. Channel Frequency Assignments (CABLE) Ch # Center Freq. Center Freq. Center Freq Center Freq Center Freq APPENDIX B – DTV Channel Table List for ATSC (AIR) Ch # Center Freq. Center Freq. Center Freq Center Freq Ch# Center Freq ®...

Table of Contents