1. Manuals
  2. Brands
  3. UMD Manuals
  4. IP Camera
  5. DL-3CA0M16-AR
  6. User manual

UMD DL-3CA0M16-AR User Manual

Hide thumbs Also See for DL-3CA0M16-AR:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for UMD DL-3CA0M16-AR

Summary of Contents for UMD DL-3CA0M16-AR

  • Page 2: Table Of Contents

    Content 1. Installation ..........................- 6 - 1.1. Minimum System Requirements ................- 6 - 1.2. Preparation ........................ - 7 - 1.2.1. Product introduction ..................- 7 - 1.2.1.1. Brief Specification Introduction ............- 7 - 1.2.1.2. Product Functions Introduction ............- 7 - 1.2.2.
  • Page 3 1.3.3.2.4. FTP Parameters ..............- 34 - 1.3.3.2.5. UPNP .................. - 36 - 1.3.3.2.6. Streaming Protocol ............. - 37 - 1.3.3.3 3G ....................- 38 - 1.3.3.3.1. Dial up setting ..............- 38 - 1.3.3.3.2. 3G online mode ..............- 39 - 1.3.3.3.3.
  • Page 4 1.3.3.6.4. Server-end Snapshot Parameters ......... - 59 - 1.3.3.6.5. Server-end Storage Device ..........- 60 - 2. Frequent Asked Questions ....................- 61 - 2.1. Fail to Access the IP Camera through the Browser ..........- 61 - 2.2. Can Not Play Video after Program Updating ............- 62 - 2.3.
  • Page 5 3.5.2.1.5. Connect the 3G IP device and forwarding server ....- 93 - 3.5.2.1.6. Set forwarding username and password ......- 94 - 3.5.2.2. Visit the 3G IP device via the forwarding Server ......- 96 - 3.5.2.2.1. Configure the CMS ............. - 96 - 3.5.2.2.2.

  • Page 6: Installation

    1. Installation 1.1. Minimum System Requirements The IP device provides access through an embedded web server. To access the device, your PC needs to meet minimum requirements to perform satisfactorily. Pentinum 4 2.4GHz and above Memory 128 MB or above Windows XP with SP2 or above.

  • Page 7: Preparation

    1.2. Preparation 1.2.1. Product introduction 1.2.1.1. Brief Specification Introduction  H.264/MJPEG/MPEG4 video compression  Resolution:2592*1920 ， 2048*1536 ， 1920*1080, 1280*720, 704*576, 704*480, 704*288, 704*240, 640*480, 352*288, 352*240, 320*240  Alarm I/O support motion detection, date, time, event trigger  Two-way audio, broadcast system ...
  • Page 8 Ultra HD IP AIO Camera ( DL-3CA0M16-AR ) Product Image: Sensor Sensor Type 1/3 "3.1 megapixel progressive scan CMOS Maximum Image Size 2048(H)×1536(V) Color 0.6 lux@ F1.6 Minimum Illumination 0.08 lux @ F1.6(0 lux @ IR ON) Shutter Speed 1/30 sec to 1/4000 sec...

  • Page 9: Network Preparation

    1.2.2. Network Preparation IP device accesses through Internet Explorer browser. Please set up the correct IP address firstly. 1. Setup your PC network The IP address of your PC must be in the same subnet with the IP device. You need to match the TCP/IP settings with PC before you can access it via IE.
  • Page 10  STEP2 Click the [Start] and select the ―Control Panel‖  STEP3 Select the ―Network and Internet connections‖. - 10 -...
  • Page 11  STEP4 Select the ―Network and Sharing Center‖  STEP5 Select the ―Local Area Connection‖  STEP6 - 11 -...
  • Page 12 Click the ―Properties‖  STEP7 Select the ―Internet Protocol Version 4 (TCP/IPv4)‖ - 12 -...
  • Page 13  STEP8 Select the ―Use the following IP address‖, enter the IP address and subnet mask. For example, you can set up your PC IP address: 192.168.1.200  STEP9 Click the [OK] and close all the dialog windows one by one. - 13 -...

  • Page 14: Configuring The Ip Device

    1.3. Configuring the IP Device Once all preparations of PC have been done, you can login the IP device through Internet Explorer Browser 6.0 or above. Follow the procedures below to configure the IP device.  STEP1 Enter the default IP address of the IP device on Browser: http://192.168.1.19 ...
  • Page 15  STEP3 Close the web browser, install and run the Installplug Click ―Tool‖ ―Internet Options‖ ―Security‖ ―Custom level‖, enable the ―Download signed ActiveX controls‖, click ―OK‖ and restart the web browser.  STEP4 Enter User name and Password. (Default user name is 888888, default password is 888888), then click ―OK‖.

  • Page 16: Real-Time

    1.3.1. Real-time 1.3.1.1. Video Control Click ―TCP‖ to transmit TCP stream Click ―Multicast‖ to transmit Multicast stream Click ―Play‖ button, to view real-time video Click ―Stop‖ button, to stop watching the video. Click ―Relay on/off‖, the button icon will become Orange.

  • Page 17: Pan/Tilt Operation

    1.3.1.2. Pan/Tilt Operation Click the right buttons to control the rotation from Up, Down, Left, Right and auto rotation. Iris+, Iris-, Focus+, Focus-, Zoom+, Zoom-; PTZ Speed is to control the movement of speed dome IP device with PTZ function. Set up preset place：Adjust the view point where you want to set, input the number, for example, 1, click ―Preset‖...
  • Page 18 Preview zoom in Click the icon, then click the image to select where you want to zoom in, release the mouse. Then the image will digital zoom in. Anti-split, to anti the screen split sometime. - 18 -...

  • Page 19: Real-Time Video Function

    Set up video delay frame, 0/5/10/20/50/100 frame optional, to make video more smooth. 1.3.1.4. Real-time Video Function 【Audio】Click ―Audio‖ button, the button icon will become orange. Connect a pickup with the IP device correctly, you will be able to hear the sound from the IP device via your computer. Please refer to the following chapter to set the audio parameters: 1.3.3.3.6.
  • Page 20 NOTE: If the computer system is Vista or Win7, you might fail the capture when clicking “snapshot”, thus, please close the browser, right-click the browser ， icon, click "Run as administrator" use administrator privilege to operate can solve this problem. 【Record】Click ―Record‖...

  • Page 21: Replay

    1.3.2. Replay This interface is to replay the video. Click ―Replay‖ to enter. When your first time to enter this interface, there is an adding-on Active X control notices to display on Internet Explorer. Please click ―Install‖ to install this plug-in, otherwise you cannot view the replay. 【Local PC storage】...

  • Page 22: Query Type

    1.3.2.1. Query Type Select the recording time to replay, click ―Search‖, there will display the file list in the segment time under the ―File List‖. 1.3.2.2. File List Choose the one you want to replay and click matching icon to playback. - 22 -...

  • Page 23: Play Toolbar

    1.3.2.3. Play Toolbar 【Progress bar】Click in the progress bar to show the current broadcasting schedule, and adjust the broadcasting pace. Play the recording. Suspended play. Stop play. Per click ―Step‖, the playback will play only a frame recording. For example, one second NTSC recording is composed by 30 frames pictures, then you need to click ‖Step‖...

  • Page 24: Settings

    1.3.3. Settings 1.3.3.1. Basic Parameters 1.3.3.1.1. Device Name 【Device Name】Input the name of the device, then click OK to save. You can modify the name. Device name usually displays in the recording files name and snapshot file name, to distinguish other videos. The device name won’t display in the ―Real –time‖...
  • Page 25 Click ―edit manual‖, select device time zone and date. Then click ―Synchronization‖ 【 】 synchronization with PC system Click ―synchronization with PC system‖. 【 】 synchronization with NTP server Input the NTP server parameters in settings, Click ―OK‖ - 25 -...

  • Page 26: Video Loop-Back Output

    1.3.3.1.3 Video loop-back output 1.3.3.1.4. User Management . You can modify them here, then click ―OK‖ button. This modification requires logging in the webpage again to browse real-time video. Default Admin User name/Pwd is: 888888/888888, Admin User has all the right to operate all the function and setting of the IP device.

  • Page 27: Time To Reboot

    1.3.3.1.5. Time to Reboot This function is used for rebooting the IP device as long as the power is on. Keep the ―Timing to Reboot‖ ―On‖ status, set the ―Reboot Time‖, for example, set ―1H5M‖, that is to say, the IP device will reboot on 01:05 every day as long as the power is on.

  • Page 28: System Update

    1.3.3.1.7. System Update This is used for system upgrade. Click ―Browse…‖to choose upgrade files of ―*. itm‖ format, and then click ―OK‖, until the webpage displays ―The program has been updated successfully, please login again‖, the device will reboot automatically. Upgrade files are provided from your supplier.

  • Page 29: Ip Address & Port

    1.3.3.2.1. IP Address & Port To access the IP device via WAN, you must map the ports first, please refer to: 3.2 Mapping & Access IP Device via WAN 【Connection type】 Static IP Address, PPPOE, DHCP optional.  Static IP Address, this method is highly recommended. ...
  • Page 30 keep the default ( Default IP address cannot be used with two and more IP devices on LAN).  Gateway Based on network environment/ IP address to fill out.  Subnet Mask Based on network environment to fill out, or keep the default. ...

  • Page 31: Wifi Parameters

    【Alarm Host Address】Alarm Host Address, keep the default. 【Alarm Host Port】Alarm Host Port, keep the default. 【Remote Host Address】Remote Host Address. This function is used IP device initiative send date to remote host. Keep the default. 【Remote Host Port】Remote Host Port. The default is 3004.

  • Page 32: Ip Address Configuration

    【IP Address Configuration】 There are three methods to enable WIFI function: Static IP Address/PPPOE/DHCP.  Static IP Address  PPPOE If you choose to PPPOE, please contact your network operators, to provide the ―PPPOE User Name‖ and ―PPPOE Password"‖  DHCP The following parameters will keep the same under these three methods.

  • Page 33: Ddns

    address  Subnet Mask Based on network environment to fill out  Gateway Keep this item the same with the IP address of your wireless router.  DNS Keep the same with your route’s DNS. This item related to the application of DDNS (Dynamic Domain Name Server) and Email Alarm.

  • Page 34: Ftp Parameters

     STEP4 DDNS Server Address, DDNS Server Port, Update Interval. Use the system default parameters.  WEB Mapping Port must keep the same as WEB Port of ―IP STEP5 Address & Port‖. 1.3.3.2.4. FTP Parameters This function is used for uploading the files to FTP server. You must have an FTP server, if you don't have, you cannot use this function.
  • Page 35  STEP3 Setting FTP scheduled recording. For example: set to upload recording files of IP device on Monday 0:10am, and stop upload on 23: 59pm.  STEP4 You can see the same video on the FTP server. - 35 -...

  • Page 36: Upnp

    1.3.3.2.5. UPNP UPNP is a quick way to discover the IP device on the network. Via UPNP function, the above ports could be mapped automatically in the router. External IP Address: WAN IP address of the router. How to use UPNP function: ...

  • Page 37: Streaming Protocol

     STEP2 If ―State‖ display ―Mapped‖, means UPNP settings is successful, please refer to the above picture. Then, please follow the below procedures to access the IP device via WAN: http://External IP Address:Web Port. If External IP is: 119.145.0.165 and Web Port is 80.The address is: http://119.145.0.165:80 NOTE: The router must support UPNP and keep “On”...

  • Page 38: Dial Up Setting

    1.3.3.3 3G 1.3.3.3.1. Dial up setting 【Link Mode (the second one)】On 【Tel Numbers】Dial-up number, provided by your 3G supplier 【Username】Username of SIM card 【Password】Password of SIM card 【APN Name】Access Point Name, provided by your 3G supplier 【Authencation Type】Auto/PAP/CHAP/NONE, keep default auto 【LCP echo interval】Keep default - 38 -...

  • Page 39: Online Mode

    【LCP echo failure】Keep default 【MRU】Keep default 【MTU】Keep default 【Network Select Type】Keep default 【Radio Band Set】Keep default 【Band saving】Keep default 1.3.3.3.2. 3G online mode 【Always online】Select Always online 【Scheduled】Manual setting 【SMS or dialing activation】SMS or dialing the SIM number to active the 3G IP device.

  • Page 40: Network

    SMS: Send ―OPEN‖ to the SIM number to active the 3G IP device Dial: dial the SIM number to active the 3G IP device  Auto offline when non-network connections: you can choose whether offline automatically when non-network connection in certain seconds. ...

  • Page 41: Dial Log

    1.3.3.3.4. Dial log If there is no log, please check whether SIM card is available. 1.3.3.3.5. 3G Status These five factors display automatically. You can not change them 【Signal Strength】 An index of the 3G network signal strength, if value is more than 20, that means the signal is good.

  • Page 42: Pin Code

    1.3.3.3.6. PIN Code 1.3.3.3.7. SMS Settings 【Days】the SMS’s validity when 3G dial up successfully, for example, if your cell phone is off for 2 days, the Days is 3, you will get the SMS in 3 days. 【Cell Phone Number】The receiver cell phone number. 【Content】When the 3G IP device is online, the SIM card will send you a SMS to your cell phone number, you can configure the content here.

  • Page 43: Channels Parameters

    1.3.3.4. Channels Parameters 1.3.3.4.1. Character Superposition 【Channel Name】To distinguish different equipment. But it won't show in preview screen. Keep the default. 【Time Type】 Choose the time type from the four formats. 【Character1】,【Character2】Input the characters to be displayed in video superposition. You type what you want to display on the real-time screen. 【Location】To adjust character position.

  • Page 44: Video Coding

    NTSC system, X is 0-672 and Y is 0-448. 1.3.3.4.2. Video Coding 【Network Transfer Stream】This is a main stream of IP device. This stream is used for IE View.  Resolution——Five image resolutions available: 1080P@30HZ,1080P@25HZ,720P@30HZ,720P@25HZ, 4CIF(D1)  Bite Rate Type——―Constant‖ and ―Variable‖. If you choose ―Constant‖, it ensures transmission fluency.

  • Page 45: Ptz Protocol

     MAX. Bite Rate The higher the Bite Rate is, the clearer the image is. More bandwidth is needed for higher Bite Rate.  Quality Upper Limit——the highest quality is 2. Keep the default.  Quality Lower Limit——the Lowest quality is 31. Keep the default. ...

  • Page 46: Adjust Color

    Data Bit: default 8 Stop Bit: default 1 Check Bit: default None Update PTZ Protocol: Select a PTZ Protocol to match P/T, click ―OK‖. 1.3.3.4.4. Adjust Color 【Brightness】Brightness adjustment. 【Contrast】Contrast adjustment. 【Saturation】Saturation adjustment. 【Hue】Chromaticity adjustment. - 46 -...

  • Page 47: Area Shield

    1.3.3.4.5. Area Shield This function is used for privacy shield protection. You can set total 4 areas. 【Area】The default Area 1 icon is green, but without any privacy shield area setting . Please enable the ―Area Shield On-off‖, Left click in the video on the left side, hold on and move, release the mouse to finish the shield for Area 1.

  • Page 48: Region Of Interest

    1.3.3.4.6. Region of Interest Set ROI Demo Select one or two ROI, the real-time video resolution of ROI will have six level for choice: best/better/good/bad/worse/worst. - 48 -...

  • Page 49: Sensor

    1.3.3.4.7. Sensor Day Night Control: Color (for color image), Black (for black and white image) Mirror Control: On or off mirror image. Vertical Mirror: On or off vertical image. Noise Level: Auto or manual noise level. WDR: On or off WDR. Sharpen: 0~255 adjustable.

  • Page 50: Day/Night Switch

    1.3.3.4.8. Day/Night Switch At day mode, image is color, will be good quality at day. At night mode, image is black and white, will be good quality at night. 【Day and night transformation mode】 Manual: manual transformation Timed: timed transformation Infrared: transformation according to infrared.

  • Page 51: Alarm Parameters

    Audio out volume: 0-100 1.3.3.5. Alarm Parameters 1.3.3.5.1. Sensor Detection Schedule Settings This function is used for setting the sensor detection Schedule. To use this function, please connect alarm sensor to the IP device. If you want to upload sensor detection recording file of IP device on Monday 0:10 AM, and stop upload on 23: 59 PM.

  • Page 52: Motion Detection Area Settings

    1.3.3.5.2. Motion Detection Area Settings 【Sensibility Adjusting】 Sensitivity adjustment. 1 to 99 Adjustable. Suggest to use the default parameters, if sensitivity adjustment is too higher, which can cause unnecessary alarm. Left click the real-time area and move to choose the motion detection area. ...

  • Page 53: Motion Detection Schedule Settings

    1.3.3.5.3. Motion Detection Schedule Settings This function is used for setting the motion detection Schedule. To use this function, please connect an alarm sensor to the IP device. If you want to upload motion detection recording file of IP device on Monday 0:10 AM, and stop upload on 23: 59 PM.

  • Page 54: 5.4.Networkabnormaldetection

    1.3.3.5.4.NetworkAbnormalDetection 【Enable Network Abnormal Detection】Start Network abnormal detection. 【Start Server-end Recording while Alarming】Store the alarming recording in server-end TF card or NAS Server. 【 Triggering Alarm Output 】 Enable this function to trigger the Network abnormal detection alarm output. 【Start Server-end Snapshot】Upload Network abnormal detection captured picture to TF card or NAS Server.

  • Page 55: Email Alarm Settings

    default parameters, if sensitivity adjustment is too higher, which can cause unnecessary alarm. 1.3.3.5.6. Email Alarm Settings This is an email alarm function. When the motion detection is enabled, IP device will set an alarm email to receiver’s mail box which you fill in. NOTE: Your email has to support the SMTP protocol, you’d better check with your email supplier.
  • Page 56 【Test】After you fill in all the parameters, please click ―Test‖ button to test. If the notice ―Successful‖, it means all information are correct and you can use email alarm function. If the notice is ―Connect mailsever failed‖, please check the parameters again.

  • Page 57: Server Storage

     STEP4 Click ―Test‖ button to test all parameters. If all are correct, email alarm will be triggered by motion detection. ： NOTE There is no request for Receiver's Email as long as it is valid. But the Sender's Email must be able to receive email via software like foxmail or outlook. The best choice is the tariff email box.

  • Page 58: Server-End Timing To Record

    1.3.3.6.1. Server-end Timing to Record This IP device supports SD card to store the recording, the max capacity is 32GB. Here you can set the time of video recorded to the SD card. Please enable the timing recording first. 1.3.3.6.2 FTP Scheduled record This function is used for automatically uploading the recording to the FTP server according to the schedule.

  • Page 59: Server-End Timing To Snapshot

    1.3.3.6.3. Server-end Timing to Snapshot In this function, you can set the snapshot parameters. 【Snapshot Time Interval】Please set the snapshot time interval, from 10-3600 seconds. 【Start Timing Snapshot】Please choose the time to activate the snapshot 【FTP Upload after Snapshot】Please refer to the chapter 1.3.3.2.6 FTP Parameters 1.3.3.6.4.

  • Page 60: Server-End Storage Device

    1.3.3.6.5. Server-end Storage Device Cut off the power, insert the TF card, click ―Format‖, then reboot and login in the IP device, there will display the info of the TF card in this interface, then you can use TF card function now. Set up NAS Server first, select ―NAS harddisk‖...

  • Page 61: Frequent Asked Questions

    2. Frequent Asked Questions 2.1. Fail to Access the IP Camera through the Browser  Possible Cause: The network is disconnected? Solution: Connect PC to the network to test whether the network access can work normally. Firstly clear the cable fault and the network fault caused by PC virus till Ping the network between PCs successfully.

  • Page 62: Can Not Play Video After Program Updating

     Possible Cause: IP address is located in different subnets. Solution: Check the settings of the IP address of IP camera, the subnet mask address and gateway.  Possible Cause: Unknown Solution: Restore to the factory-set default state by pressing the restore button behind the IP camera.

  • Page 63: Errors Occur After Updating

     When configuring the firewall rule, whether take IP camera into account.  Solution:  Before searching the network fault, please make sure to use the ping command in the command mode to connect the IP address. To check the message returned from ping is a very important step.

  • Page 64: Appendix

    3. Appendix 3.1. Hardware Reset After updating the IP device, or when there are some problems that you can’t solve via reboot, for example, you can’t get the IP address via the search tool, please try to reset the IP device. After this reset, all the parameters will be back to the factory default, the IP address will be back to default: 192.168.1.19.
  • Page 65  Step 1 Cut off the power of IP device, all the indicate lamps are off.  Step 2 Press the ―RST‖ button with a pin, don’t release.  Step 3 Connect the power to the IP Device, the ―STATE‖ indicate lamp will flicker.

  • Page 66: Mapping & Access Ip Device Via Wan

    3.2. Mapping & Access IP Device via WAN Access IP device via WAN is a very important network function, using this function, you can access your IP device anywhere anytime. To access the IP device via WAN, you must map some related ports to the WAN via router.
  • Page 67 ports. Web Port: Default is 80 Data Transfer Port: Default is 3000, Data Control Port: Default is 3001 Remote Transfer Port: Default is 3002 【WEB Port】 Default is 80. It is a very important port to recognize the IP device. This 80 web port is dropped acquiescently, for example, if the IP address of your IP device in LAN is 192.168.1.19:80, the default IP address will be 192.168.1.19.

  • Page 68: Upnp Mapping

    using the IP address. 【Data Control Port】 Default is 3001. It is a hidden port in the background system. It has a certain conversion relation with the Data Transfer Port: Date control port = date transfer port + 1. If you change the date transfer port into 4000, the system will automatically change date control port is 4001.

  • Page 69: Manual Mapping

    3.2.2. Manual Mapping Via manual mapping, you have to map the ports in the router by yourself. Different routers have different interfaces and methods. Take Cisco LINKSYS WRT54G2 for example.  Step 1 Manual mapping Access to the router’s interface via IE: ―Applications & Gaming‖―Port Range Forward‖, Please map the real ports of your IP device, here take the default ports for example.
  • Page 70  Step 2 Check the Status and access Access to the ―Status‖ to check the WAN IP address. If the WAN IP address is 119.145.0.165, the IP address of the IP device will be http://119.145.0.165:80 http://119.145.0.165 when you access via WAN. - 70 -...
  • Page 71 - 71 -...

  • Page 72: Wireless Settings

    3.3. Wireless Settings WIFI function is a powerful function that makes your IP device getting out of the limit of network cable in a certain distance. You can put your IP device anywhere with an adapter in this distance, and access it freely. First, you have to have a wireless router to work with the wireless IP device.
  • Page 73  Step 2 Set Wireless Security Security Mode: Select ―WPA2 Personal‖ WPA Shared Key: Set this key freely and remember it. For example: 33265782 Please keep the other settings to be defaults. Then save these settings via ―Save settings‖, and close the router. Login the router again. - 73 -...

  • Page 74: Set The Ip Device

    3.3.2. Set the IP Device - 74 -...
  • Page 75 Login the IP device via Internet Explorer, access to the “Setting” ―Network Parameters‖ ―WIFI Parameters‖,  Step 1 Press ―Refresh‖ to search the SSID and the Encryption Type  Step 2 Fill in the following info: Currently Wireless Network: kf, the SSID Input Password: 33265782, the ―WPA Shared Key‖...

  • Page 76: Check The Wireless Settings

     DHCP, this is the easiest way to use WIFI function.  Step 4 Enable the ―WIFI Gateway as Default Gateway‖  Step 5 Select the ―WIFI specification‖: 802.11b&802.11g  Step 6 Click ―OK‖  Step 7 Save and reboot the IP device 3.3.3.
  • Page 77 - 77 -...

  • Page 78: How To Use The Streaming Protocol

    3.4. How to Use the Streaming Protocol These two streaming protocols are for higher requirement users and broadcasting clients. VLC player is necessary for this function, the following guide is based on the latest version of: VLC media player 1.1.7. 【RTSP】RTSP is Real-Time Streaming Protocol, to transfer the multimedia audio and video streaming.
  • Page 79  STEP2 Use the players which support the RTSP function to play the streaming. For example: use VLC player to play the RTSP streaming. Here it is the method to use the VLC player: Install the public VLC player software from the internet. Following the diagrams: - 79 -...
  • Page 80 The RTSP address is: rtsp:// 192.168.1.19:554/0/1:1/main, formed as below: 192.168.1.19: IP address of the IP device 554: RTSP listen port Default port, cannot be changed 1:1: Common User name & password, Please refer to:1.3.3.1.3 User Management main: Main streaming, In summary, the RTSP streaming is for main streaming of the rtsp://192.168.1.19:554/0/1:1/main.
  • Page 81 Sub streaming: rtsp://192.168.1.19:554/0/1:1/sub The third streaming: rtsp://192.168.1.19:554/0/1:1/2sub The setting of video coding setting, please refer to: 1.3.3.3.2 Video Coding 【TS】TS is transfer streaming. It is an audio, video and data communications transmission protocol that is specified in MPEG-2 Part 1. The transport stream allows for multiplexing of the digital video and audio.
  • Page 82  STEP4 To open players and play TS streaming. For example: using VLC player to play. Click ―Media‖—Select ―open network stream‖, then, in ―Network‖. Fill in TS destination address: udp://@235.1.1.1:1234 The diagram is as below. - 82 -...

  • Page 83: User Guide

    3.5. 3G User Guide Before using the IP device, please make sure the 3G signal is good, SIM card is available. 3.5.1. Set the 3G parameters  STEP1 Insert standard 3G SIM card into the SIM card slot of the IP device. (Please use a tiny stick to press into the hole at the right side of the slot, to pop the slot.) ...

  • Page 84: Dial Up Setting

    3.5.1.1. Dial up setting 【Link Mode (the second one)】On 【Tel Numbers】Dial-up number, provided by your 3G supplier 【Username】Username of SIM card 【Password】Password of SIM card 【APN Name】Access Point Name, provided by your 3G supplier 【Authencation Type】Auto/PAP/CHAP/NONE, keep default auto 【LCP echo interval】Keep default 【LCP echo failure】Keep default 【MRU】Keep default 【MTU】Keep default...

  • Page 85: Online Mode

    3.5.1.2. 3G online mode 【Always online】Select Always online 【Scheduled】Manual setting 【SMS or dialing activation】SMS or dialing the SIM number to active the 3G IP device. SMS: Send ―OPEN‖ to the SIM number to active the 3G IP device Dial: dial the SIM number to active the 3G IP device ...

  • Page 86: Network

     Auto offline when non-network connection ―Connect‖, dial on manually, ―Disconnect‖ dial off manually 3.5.1.3. 3G network 【3G Status】If the status is Connected, that means the 3G network works. At the same time, the other parameters will be formed automatically, so does the 3G IP device 3.5.1.4.

  • Page 87: Status

    3.5.1.5. 3G Status These five factors display automatically. You can not change them 【Signal Strength】 An index of the 3G network signal strength, if value is more than 20, that means the signal is good. The higher the value is, the stronger the signal is.
  • Page 88 【Days】the SMS’s validity when 3G dial up successfully, for example, if your cell phone is off for 2 days, the Days is 3, you will get the SMS in 3 days. 【Cell Phone Number】The receiver cell phone number. 【Content】When the 3G IP device is online, the SIM card will send you a SMS to your cell phone number, you can configure the content here.
  • Page 89 Here provide some diagrams of 3G IP device viewing. Diagram of viewing IP device directly: Forwarding server： - 89 -...

  • Page 90: Set Forwarding Server To View 3G Ip Device

    3.5.2. Set Forwarding server to view 3G IP device 3.5.2.1. Configure Forwarding Server Install software RealCDMA to your PC 3.5.2.1.1. Set “RVS Service Port” and “Transmit Port” ―Operation‖―System Configure‖ 【RVS Service Port】default: 3004 【Transmit Port】default :4000 【 Narrowband Program 】 Choose this function, only when you use the ImagineWorldClient to access the IP device, that the IP device will upload the data to the forwarding server.

  • Page 91: Mapping The Forwarding Server-Rvs Service Port

    3.5.2.1.2. Mapping the forwarding server—RVS service port There are 4 ports you need to do mapping in the router ,RVS service Port, Transmit Port, Transmit Port + 1, Transmit Port + 2 (For example, Default RVS Service Port: 3004, Default transmit port: 4000, so you need to do mapping of these ports: 3004, 4000,4001,4002) Take D-LINK router and RVS service port for example: Open router interface in web browser, go to the ―Forwarding‖‖Virtual servers‖...

  • Page 92: Check The Forwarding Server Wan Ip Address

    3.5.2.1.3. Check the forwarding server WAN IP address ―Device Status‖―Status‖  ―WAN‖  ―Network Status‖ For example，119.145.0.162 is forwarding server WAN IP address 3.5.2.1.4. Make sure the port mapping is successful Run from ―Start‖, input ―CMD‖ then enter command, telnet the IP address port number, for example: telnet 119.145.0.162 3004, enter command If feedback displays like the following, means mapping is successful.

  • Page 93: Connect The 3G Ip Device And Forwarding Server

    3.5.2.1.5. Connect the 3G IP device and forwarding server To upload the data to the forwarding server from the 3G IP device, the Remote Host Address of the 3G IP device should be the forwarding server’s WAN IP address, the Remote Host Port of the IP device should be the same with the RVS Service port.

  • Page 94: Set Forwarding Username And Password

    3.5.2.1.6. Set forwarding username and password Open the ―RealCDMA‖ software ―Operation‖User Manage‖Transmit User Manage‖, the Username and Password are set by users - 94 -...
  • Page 95 Now, please wait for the 3G IP device to be online in forwarding server. If displays like the following picture, it means the 3G IP device connects with the forwarding server successfully, we can visit 3G IP device via the forwarding server. - 95 -...

  • Page 96: Visit The 3G Ip Device Via The Forwarding Server

    3.5.2.2. Visit the 3G IP device via the forwarding Server 3.5.2.2.1. Configure the CMS Open ImagineWordClient software, ―Option‖―Server Management‖  ―Add Project‖  ―Add Group‖  ―Add server‖ 【Server Name】 IP Device name, named by users 【Server Address】Forwarding server WAN IP address 【Data Port】...

  • Page 97: Visit Via Web Browser Of Ip Device

    After add 3G IP device successfully, drag ―Camera‖ icon to the channel of right windows, then you can view the video of IP device NOTE: Since the 3G network is very small, if the network transfer stream bite rate is too big, the video of IP device will be delay. Users can change the parameters to achieve better effect.
  • Page 98 Now you could visit the 3G IP camera on the web browser. - 98 -...

Table of Contents