Advertisement
set and aligned with discharge
base the same as described for
the rail guide plate attached to
the frame.
Installing
Intermediate
Guide Bracket
(Fig. 6)
Guide Rail Length
IGB Required
21 Ft. or less
21 Ft. to 40 Ft.
Over 40 Ft.
1. Remove guide rails (Fig. 3),
and cut a piece from each
one. These pipes must be
exactly the same length and
of a length that will permit
installing the intermediate
guide bracket in the desired
location.
2. Place the cut pieces of pipe
over the guide rail pins
located in the base.
3. Set the intermediate guide
bracket in position with
tapered guides into pipes. Put
U-bolt around discharge pipe
and tighten lightly.
4. Measure from joint on tapered
plug on intermediate guide
bracket to joint of tapered
plug on top rail support and
cut two rails to this length.
Put rails in place and tighten
Part
Model
Number
52773-051-7
TL23HH-LE
52773-050-7
TL23HH
52773-053-7
TL33HH-LE
52773-052-7
TL33HH
52773-054-7
TL34HH
52773-073-7
TL44HH-LE
52773-070-7
TL44HH
52773-071-7
TL46HH
52773-072-7
TL48HH
4
screws in top rail support.
Holes are slotted to adjust for
any error in rail pipe length.
5. Recheck rails; they must be
straight and plumb. Move
intermediate guide bracket
if necessary to perfectly
align rails. After alignment
is secured, tighten nuts on
U-bolt.
6. If a second intermediate
guide bracket is used, the
above procedure is followed
for installation.
0
1
Attaching
2
Mounting Plate
to Pump
1. Attach the mounting plate
with
the
(See Parts List, page 5.)
The mounting plate should
be turned so that the two
locating pins are horizontal
when attached to the pump
discharge.
2. Mount the guide plate to the
mounting plate using the two
set screws provided.
Installing
Pump and
Mounting Plate
1. Attach the lifting chain to
the pump. This is done by
installing two eye bolts.
Pump
Discharge
Elbow Size
N/A
2.5
N/A
3
3
N/A
4
4
4
supplied
bolts.
System
Base
Discharge
Part Number
N/A
25068D001
3
25068D001
N/A
25068D003
3
25068D003
4
N/A
25068D002
4
25068D002
6
25068D002
8
WARNING: Do not exceed
working load limit of chains
and other lifting devices.
Do not use chains or lifting
devices where failure could
result in loss of life. Examine
chains and lifting devices
for deformation or damage
before and after each lift.
2. A hook is located on the top
rail support (Fig. 3) to hold
the upper end of the chain
when not in use.
3. Position pump so the guide
rails are located in the slots of
the guide plate. Slowly lower
the pump down the guide rails
to the base. The locating pins
(horizontal pins on mounting
plate) should come to seat
in the inclined surface of the
arms.
CAUTION:
No
should be in the sump basin
when pump is lowered into
position!
Air Venting:
Air tends to trap in the pump
volute when water rises in the
sump or when the pump is
lowered into water after service.
To vent off this air, a small hole
is drilled into the pump volute.
Be sure this vent hole is clean
after any service work on pump.
Air venting is not a problem after
initial start.
Flange
Part Number
25069D012
25069D012
25069D015
25069D015
RTF
25069D014
25069D014
25069D014
RTF
persons
Elbow
Part Number
N/A
23497A103
N/A
23497A103
N/A
23497A101
25046A101
Advertisement
