Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Cablescan QS-200S
- Page 1 ELECTRONIC ASSEMBLY AID QS-200S Cablescan...
-
Page 3: Instruction Manual
March 25, 2005 QS-200S INSTRUCTION MANUAL (Part Number 5900159) Cablescan A Eubanks Company 3022 Inland Empire Blvd. Ontario, California 91764 (909) 483-2436 Fax (909) 483-2463 www.cablescan.com... -
Page 4: Warranty
Cablescan, Inc., manufactures its products in a manner to be free of defects. Should any defect of manufacture occur in its products within one (1) year from date of shipment by it, Cablescan, Inc., upon prompt notification, will at its option, either exchange or repair. -
Page 5: Table Of Contents
TABLE OF CONTENTS WARRANTY..................... IV GENERAL DESCRIPTION ..............VI SPECIFICATIONS .................. VII INSTALLATION ..................1 Power Requirements ................... 1 Grounding Requirements................1 Instrument Positioning ................. 1 Repair ......................1 OPERATING CONTROLS & INDICATORS ..........2 OPERATING INSTRUCTIONS ..............4 Introduction ....................4 Front and Rear Panel Features ..............4 Before Initial Power-On................ -
Page 6: General Description
QS-200 Instruction Manual GENERAL DESCRIPTION The Cablescan Model QS-200S provides a versatile method of identifying and terminating cable and harness assemblies. Its use eliminates the need for color-coding, number stamping or tagging, and 'ringing out' with buzzers or ohmmeters. This production identification tool has the ability to rapidly search wires using the operator's fingertips. -
Page 7: Specifications
SPECIFICATIONS CAPACITY: 200 wires SWEEP TIME: 350 msec. INTERWIRE CAPACITANCE: > 5,000 pf (Scan and Preselect Modes) > 6.8 MΩ (Body current limited to 6 μA) INPUT SENSITIVITY: DISPLAY TIME: Analyze: approximately 500 msec. Scan: modulated at a 25 Hz rate when multiple wires are present MULTIPLE WIRES: At least 20 wires displayed... -
Page 9: Installation
POWER REQUIREMENTS The QS-200S operates on line voltages of 104-126 and 208-252 V~, 50-60 Hz. A label on the back panel indicates the correct voltage for the unit. CAUTION: To avoid instrument damage, the power transformer must be wired correctly before applying line power;... -
Page 10: Operating Controls & Indicators
Used to position the front panel for operating convenience. SCAN INPUTS: Four connectors J1 (1-50), J2 (51-100), J3 (101-150), J4 (151- 200), are inputs to the QS-200S for the cable or harness being identified. TONE: A pulsating audio tone will sound when the preselected wire has been activated by body conductance. -
Page 11: Front Panel
QS-200S Instruction Manual Page 3 Q S -2 0 0 S W IR E N U M B E R 0 4 3 P R E S E L E C T S C A N A N A LY Z E... -
Page 12: Operating Instructions
PRESELECT interlocked mode switches. SCAN MODE With the SCAN switch depressed, the QS-200S operates with a short dwell time. If a single wire is contacted, the display will show the coded number corresponding to the wire contacted. (The code is determined by the interface cable assembly connecting the wire network to the QS-200S). -
Page 13: Maintenance
J1 and J2 on the scanner assembly to the rear panel. The scanner assembly may then be placed component side up in front of the QS-200S. The second scanner can be removed in the same manner. If complete detachment is necessary, unplug the cable assembly from the scanner assembly. - Page 14 Page 6 QS-200 Instruction Manual NOTES...
- Page 15 Cablescan 5900159 Rev F...
Need help?
Do you have a question about the QS-200S and is the answer not in the manual?
Questions and answers
Why will the power button not stay down, but pops right back up?
The power button on a Cablescan QS-200S may not stay down and could pop back up if the instrument is not properly grounded. According to the manual, the instrument will not operate reliably unless it is properly grounded through the offset pin of the power cable when plugged into an appropriate receptacle.
This answer is automatically generated
@Mr. Anderson I plugged it into another outlet, and the button stays down. Now it doesn’t display anything.