Advertisement
Quick Links
TO BE PLACED NEARBY THE CHANGING TABLE
Information about the use of electrical height
adjustable changing table
• Never leave the child unattended on the changing
table.
• The remote should be placed out of reach of small
children. Switch off after use
• Be aware of other children in the room while
in use
• Be aware of things placed underneath the
changing table
• All CASTORS must be locked while in use
• Changing table only to be used by the staff
• Please read the complete manual and remember
to instruct new staff about the use of the changing
table
IMPORTANT !
1
Advertisement
Related Manuals for CONSET BSR 107
Summary of Contents for CONSET BSR 107
- Page 1 TO BE PLACED NEARBY THE CHANGING TABLE IMPORTANT ! Information about the use of electrical height adjustable changing table • Never leave the child unattended on the changing table. • The remote should be placed out of reach of small children.
- Page 2 Electric Height adjustable changing table ConSet® - Type BSR 105+107+117+119 BSR 107 BSR 119 BSR 117 BSR 105 DIRECTIONS OF USE/ASSEMBLY WARNING IMPORTANT INFORMATION! Prior to installment, use and maintenance of the table frame, any installer and any user of the changing table must study this assembly and operation manual carefully, so as to gain a complete understanding of its contents.
- Page 3 5. MAINTENANCE AND DEFECTS 6. TECHNICAL DATA 7. ASSEMBLY DIRECTIONS, WALL TYPE BSR 105+107 8. ASSEMBLY DIRECTIONS, FLOOR TYPE, BSR 117+119 9. ASSEMBLY DIRECTIONS, WASH ON SIDE, BSR 107 10. SERVICE FAQ 11. DECLARATION OF CONFORMITY SAFETY AND WARNINGS Please read the operation manual prior to start using the table. It provides you with important information about safety, use, installation and maintenance of the table, and thus protecting you and your children and avoiding damage on the table..
- Page 4 Liability: The manufacturer accepts under no circumstances warranty claims or liability claims for damages arising from improper use or handling of the table frame other than that described in this operation manual. SET UP AND INSTALLATION The changing table must be mounted by a skilled fitter or craftsman. All directions of this manual must be followed carefully.
- Page 5 7. ASSEMBLY INSTRUCTION - TYPE BSR 105+107 Mounting the top brackets: a) Mount the top brackets. Cross bar is not allowed to be removed before the frame included top has been fully assembled. b) Mount four fixing brackets for top and attach three lead holders with screws.
- Page 6 Mounting of wall bracket, top etc. c) Mount bottom wall bracket d) Mount top in pre drilled holes - place the top so the square holes in the top is symmetric placed around the columns - tighten the screws...
- Page 7 e) Mount top wall bracket f) Place the unit by the wall g) Mark for drilling (if necessary) h) Remove the unit again i) Ensure that A and B-measurements are the same j) Drill holes (if necessary) k) Mount the unit on the wall...
- Page 8 Mounting the handset: The plug from the handset and the AC cord must be inserted into the sockets and the wire from the handset attaches to the top (as shown on dotted line). Important! The handset must be placed out of reach of children.
- Page 9 8. ASSEMBLY INSTRUCTIONS FLOOR-type, BSR 117+119 a) Mount top brackets ref.page 5, mounting a) + b) b) Mount either levelers or wheels c) Mount handset The plug from the handset and the AC cord must be inserted into the sockets and the wire from the handset attaches to the top (as shown on dotted line).
- Page 10 d) Mount top in pre drilled holes place the top so the square holes in the top is symmetric placed around the columns tighten the screws e) Mount wire basket Remove the cross bar and the changing table is now ready for use. The fitter must instruct the staff in proper use and the instructions of this manual.
- Page 11 ASSEMBLY INSTRUCTIONS side sink, BSR 107 a) The side sink can be mounted in either the right or left side of the top. b) Make two ø8 mm holes in both top and sink as shown in drawing. Holes to be used with the fixing bolts.
- Page 12 d) Mount the two fixing bolts between the tops e) Finish by mounting two support brackets on the side sink The crack between the two tops can be sealed with sealant. Be sure to clean the surface with a gentle household cleanser prior to sealing.
- Page 13 DECLARATION OF CONFORMITY We hereby declare, under our sole responsibility that the following products: ConSet changing table type BSR is in accordance with: Directive 2006/42/EF of The European Parliament and of the Council of 17 May 2006 on machinery and on changes of directive 95/16/EF...
Need help?
Do you have a question about the BSR 107 and is the answer not in the manual?
Questions and answers