Sharp SJ-LC31CHXW1-EN User Manual page 6

CHAPTER -1: SAFETY INSTRUCTIONS
Installation warnings
Before using your fridge for the first time, please pay attention to the following points:
• The operating voltage for your fridge is 220-240 V at 50Hz.
• The plug must be accessible after installation.
• Your fridge may have an odour when it is operated for the first time. This is normal and the odour will fade when
your fridge starts to cool.
• Before connecting your fridge, ensure that the information on the data plate (voltage and connected load)
matches that of the mains electricity supply. If in doubt, consult a qualified electrician.
• Insert the plug into a socket with an efficient ground connection. If the socket has no ground contact or the plug
does not match, we recommend you consult a qualified electrician for assistance.
• The appliance must be connected with a properly installed fused socket. The power supply (AC) and voltage at
the operating point must match with the details on the name plate of the appliance (the name plate is located
on the inside left of the appliance).
• We do not accept responsibility for any damages that occur due to ungrounded usage.
• Place your fridge where it will not be exposed to direct sunlight.
• Your fridge must never be used outdoors or exposed to rain.
• Your appliance must be at least 50 cm away from stoves, gas ovens and heater cores, and at least 5 cm away
from electrical ovens.
• If your fridge is placed next to a deep freezer, there must be at least 2 cm between them to prevent humidity
forming on the outer surface.
• Do not cover the body or top of fridge with lace. This will affect the performance of your fridge.
• Clearance of at least 150 mm is required at the top of your appliance. Do not place anything on top of your
appliance.
• Do not place heavy items on the appliance.
• Clean the appliance thoroughly before use (see Cleaning and Maintenance).
• The installation procedure into a kitchen unit is given in the installation manual. This product is intended to be
used in proper kitchen units only.
• Before using your fridge, wipe all parts with a solution of warm water and a teaspoon of
sodium bicarbonate. Then, rinse with clean water and dry. Return all parts to the fridge after
cleaning.Use the adjustable front legs to make sure your appliance is level and stable. You
can adjust the legs by turning them in either direction. This must be done before placing
food in the appliance.
• Install the two plastic distance guides (the parts on the black vanes -condenser- at the rear)
by turning it 90° (as shown in the figure) to prevent the condenser from touching the wall.
• The distance between the appliance and back wall must be a minimum of 75 mm.
Electrical connection (For UK type plug)
For your safety please read the following information
Warning: This appliance must be earthed.
This appliance operates from 220-240 volts and should be protected by a 13 amp fuse in the plug.
The appliance is supplied with a standard 13 amp 3-pin mains plug fitted with a 13-amp fuse. Should the fuse require
replacement, it must be replaced with a fuse rated at 13 amp and approved to BS1362.
If the mains plug which is fitted is unsuitable for the socket outlet in your home or is removed for any other reason,
please follow the instructions below on how to wire a 13 amp 3 pin plug..
How to wire a 13 amp plug?
Important
The wires in the mains lead on this appliance are coloured
in accordance with the following code:
Green and Yellow - Earth
Blue – Neutral
Brown – Live
As the colours may not correspond with the markings
identifying the terminals in your plug proceed as follows.
The green and yellow wire must be connected to the
terminal in the plug which is marked with the letter E or with
the earth symbol or coloured green and yellow.
The blue wire must be connected to the terminal marked N.
The brown wire must be connected to the terminal marked
L.
You must make sure the lead is firmly secured under the
cord clamp.
Blue
Neutral
Cord Clamp
EN -5-
Green / Yellow
Earth
Brown
Live
FUSE
13 Amps