Page 2
Thank you for purchasing the IP camera tester. Please read the manual before using the IP camera tester and use properly. For using the IP camera tester safely, please first read the [Safety Information] carefully in the manual. The manual should be kept well in case of reference.
Content Content ..........................3 1. Safety Information ....................5 2. IP Camera Tester Introduction ................6 2.1 General ......................6 2.2 Product Features ..................6 2.3 Function Introduction .................. 7 2.3.1 H.265 Mainstream test ................7 2.3.2 HD display and touch operation ............... 7 2.3.3 IP camera test ...................
Page 4
2.3.20 Analog camera video test ..............10 2.3.21 PTZ control .................... 10 2.4 Packing list ....................10 2.5 Function interface ..................11 3. Operation ......................13 3.1 Battery installation and charging instructions .......... 13 3.2 Instrument connection ................13 3.2.1 IP camera connection ................13 3.2.2 Analog camera / coaxial HD camera connection * .........
Safety Information The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital, gas station etc. When using this device, please use the original accessories to avoid damage caused by ...
IP Camera Tester Introduction 2.1 General The IP Camera tester is used for the installation and maintenance of security monitoring equipment such as IP network HD cameras and analog video surveillance cameras. The device uses a 5-inch high-definition touch screen display, and the main stream can display H.265/H.264 encoded network HD camera images, the highest resolution 4K.
PING test to test whether the Ethernet port of an IP camera or other network device is working properly and the IP address is correct. IP address scanning to quickly find the IP address of an IP camera or other network ...
2.3.4 Android system This product has an Android system and supports the installation of third-party apps with Android version. 2.3.5 App Store The built-in app store allows you to upgrade your own system apps at will. 2.3.6 Audio test The audio test function of the video monitoring tester can test audio devices such as pickups in the video monitor front end.
2.3.13 Video record While video test and PTZ debug with the tester, the video can be recorded by one-click operation and stored in the SD of the device to facilitate the construction and recording of the scene. 2.3.14 Playback The device stores the video files and captured image files in the SD card, saves these files under different directories according to different dates.
2.3.20 Analog camera video test The device can display the image of an analog camera, a 4-inch 800x480 display, a larger viewing angle, and more intuitive display of camera image quality. Supports image signals in PAL/NTSC format. The backlight brightness of the LCD display of the device is adjustable, and the brightness, contrast, and color saturation of the analog video image can be adjusted.
2.5 Function interface Power on/wake up indicator Charging indicator, flashing while charging, always on when fully charged.
Page 12
Bottom interface Top inteface Micro SD card moveable, (supports up to 32GB) HDMI output interface Audio output and earphone interface RS485 Interface: RS485 communication for the PTZ LED lamp 5V USB interface, external mouse and keyboard, etc. Audio input Ethernet interface DC12V1A power output, for provisional DC power supply RESET - unexpected failure driver reset port 5V charging interface...
Operation 3.1 Battery installation and charging instructions This device has a built-in rechargeable polymer lithium battery. To ensure safe transportation, the battery connection in the battery compartment must be disconnected during transportation! (Factory added battery separator) Unplug the battery separator before use. No need to disconnect the battery when the user is in normal use.
3.2.2 Analog camera / coaxial HD camera connection * ⑴ Connect the video output of the camera or the speed dome to the video input VUDIO IN of the IPC Tester video monitoring tester. The LCD screen of the device will display the image of the camera.
3.3.2 IPC Test app When we open the IPC Test software on the main page, the software will automatically search for the IP camera device in the LAN. Clicking the camera list on the left panel will display the real-time screen of the camera. At the top left, it is the user name and password.
Page 16
When we click , we can increase the IP address and port of other devices in the LAN to match. Click to re-detect the IP camera device in the LAN. Recording: Under the screen, the icon button can perform the recording function, and the button color will change.
Page 17
When you click again, its color returns to normal, indicating that the recording has ended and is saved in the video player Screenshot:When we click the icon button at the bottom, the image on the video will be captured in real time, and the UI will also prompt the photo success. The picture will be saved in the video player Video player: When we click on the player, it will jump to the video player interface,...
Page 18
Camera information: When we click , it will display information about the camera equipment we tested, such as manufacturer, device model, device serial number, firmware version, IP Address, Mac address, etc. Setting: When we click , it will show two options, one is “IP Setting”, another one is “Time Setting”.
Page 19
IP Setting: Set IP Address of IP Camera We can configure IP address, subnet mask, network management, DNS, etc. according to the actual application scenario. Time Setting: You can synchronize time with your computer on the network, or you can manually set the time parameters.
Page 20
Code stream selection:Click to select main stream or sub stream. RTSP address query: Click to query the corresponding RTSP address and provide convenient copy function.
3.3.3 Network Tool Open the app “Network Tool” , there are three functions: (1) Network Settings This function is to set the IP address of the IPC device, the subnet mask and other data, you can choose to enable the wireless network, or wired Ethernet. (2) IP Address Scan:...
Page 22
There is a button “Search” on the page IP Address Scan. Click the search button, you can see the IP address of the valid device in the LAN. (3) PING Test: When we scan the IP of the valid device in the LAN, we can choose the IP address we want to test to see if our IPC device can communicate with it effectively.
Notes: When you maintain a network device, the most common method is to use PING to test whether the device works normally and the IP address is set correctly. Normal network communication can only be performed if PING is successful. When the PING test, the first packet may be dropped, which is normal.
When entering the flashlight interface, the LED of the device lights up, click to close the window, then the device's LED light will keep bright even if using other function. 3.3.5 Calculator When we are going to do some data calculations, our IPC device also provides a useful little program "Calculator"...
Connect the audio device (e.g. the pickup) to the “Audio input” port of the device, click to enter the recorder function interface, then click the recording button Play the sound sent by the audio device, click the stop button , stop the playback, then you can click “Cancel”...
The browser can be used to log in to the IP camera and modify the IP address of the network camera. If hope the browser can log in to the IP camera, the IP camera and device should be on the same network segment.
Page 27
Click the icon to set alarm according to your needs. Click the icon to set the countdown time. When the countdown time is over, an alarm will be given.
Click "ES file browsing" to manage internal storage or external storage files. We can see the status of each type of file, memory usage, and some tools, such as downloader, weather, Baidu, etc. 3.3.10 System setting Click the icon , then click the icon to enter System Setting window.
Input: Set the input method of the device. Other input methods can be installed as needed. Display: Backlight settings and backlight brightness adjustment are possible. Sleep time setting, 15 seconds to 30 minutes to automatically sleep, or turn off sleep, wallpaper etc. Volume setting: Set speaker volume, media volume, alarm volume;...
The power output function is mainly applied to the live demonstration and test of the camera. At the same time, for some camera installation sites, if there is no power supply before the project is implemented. The tester can offer temporary power for it. The power output of the device plays a necessary role.
Specifications Model Display 5-inch, high-definition capacitive touch screen, 800*480 resolution. Network port 10/100M auto adjust, RJ45 H.265 Mainstream New hardware decoding, 4K, H.265/H.264 camera image display by test mainstream testing. IP camera test Support IP camera with ONVIF protocol Video signal test 1 channel Video IN BNC input, support analog, AHD, CVI, TVI (optional) Video signal output 1 channel analog color bar output...