Advertisement
Available languages
Available languages
User manual for SR-1003
Your purchase and use of SR-1003 gas alarm is greatly appreciated. Please read the
operation instructions BEFORE using the device, and make sure to keep this manual
after carefully reading it, for the future reference.
1. Summary
The household gas alarm has been developed by adopting advanced electronic and gas
detecting techniques. It is highly sensitive and is applicable to detect the leakage of
household gasses, liquid gasses and natural gas. The sensor reacts with the diffused
gases in the air directly and generates linear voltage signal. When the detected gas
density reaches a certain value, the alarm emits an acousto-optic alarm signal to remind
its users to take appropriate measures in time. HS – 109B gas alarm has a modern,
smart design, and is convenient to use.
2. Technical Parameter
• Rated voltage: AC230V/50~60HZ
• Power dissipation: <6W
• Operating temperature:
-10°C
~ +
50°C
• Operating humidity: 10%~85% RH
• Alarming level of gas density: gas ≤25% LEL
• Alarm loudness / effective range: ≥85 dB @ 3 m
• Dimensions: 126*73*76 mm
3. Operation
A) Plug in the gas alarm to mains, so that it can preheat (for about 2 minutes), with red
indicator light being turned on. During this time the gas alarm does not detect gas. After
the device finishes preheating, the red indicator light will turn off. This is a sign that
shows the alarm is in a testing mode. (it may emit alarms when being plugged in to
mains, and will switch to normal operating mode after preheating, few minutes later.)
B) Testing mode: Press the test button for a few seconds, the red indicator light will
start to flash, and the gas alarm will emit sounds. Next, release the button and the red
indicator light will turn off, while sound alarm will cease, as well. This means the alarm is
working well. Install the gas alarm in desired place (after testing it) and plug it in to the
power supply accordingly.
C) Inspection mode: The red indicator light will flash every each 40 seconds.
D) In case of events, the alarm has tested the corresponding density of the gas, the
red indicator light will flash and emit corresponding sound alarms. This reminds the
users to take appropriate measures in time.
E) Press the test button with regular intervals, to make sure the alarm is in normal
operating mode and make sure to keep the surrounding area clean.
4. Installation
A) If this particular device is used to detect natural gas, please install the alarm in place
at least 50 centimeters away from the ceiling, as well as, within 1,5m distance from the
nature gas source. The main component of natural gas is methane, which
EN
PL
is lighter than air, therefore the gas alarm should be mounted on the walls
should not be placed below the top frame of doors or windows.
B) If this particular device is used to detect compressed petroleum gasses or city coal
gasses, their main components are propane or butane, which are heavier than air, hence
the alarm should be mounted in lower places, generally installed at a distance of less
than 30 cm from the ground and within a distance of 1.5m away from the LPG source.
On top of that, there should be no doors or windows located, between the alarm and
LPG source, because that prevents the leakage of the gas, from reaching the alarm for
the first time.
Gas alarm CANNOT be installed in the following places:
A) Do NOT install the alarm at the top of the cooker (similar kitchen appliances), as
smoke, fat and /or dirt may negatively affect alarm's functionality.
B) Do NOT install the alarm above the sinks (or any water containers), as water splashes
(humidity) and /or dust may negatively affect alarm's functionality.
C) Do NOT install the alarm in places, where there are air / vent holes, fans or any other
ventilated places nearby. This may prevent the leakage of gas from reaching the alarm
for first time.
D) Do NOT install the alarm in tightly-covered concealed places. This may delay the
proper detection of gas leakage.
E) Do NOT install the alarm outdoors or in places with humidity being lower than 10%
or higher than 85%.
5. Warning
A) Do use special fittings for any possible repairs, in order to avoid damaging the
product.
B) Do not repair the gas alarm by yourself. Let the professionals handle the
maintenance.
C) Make sure to keep household gas alarm and its packaging materials, out of reach of
the children.
D) Any improper use or man-made damage is not covered by the product warranty.
6. Product utilization
The packaging material is reusable. Dispose of the packaging in an environmentally
friendly way by putting it in the appropriate recyclable waste collection containers.
Dispose of the product and the batteries in view of the environment if you want to
separate. The device and the batteries must not be thrown in with domestic waste. Take
them to a recycling center for used electrical and electronic devices. For more
information you can consult your local government. Remove batteries first.
7. Warranty
The product is covered by 24-month warranty.
EN
PL
The WEEE symbol (the crossed-out wheeled bin) usage indicates that this product is
not a household waste. Appropriate waste management aids in avoiding consequences,
which are harmful for people and environment and result from dangerous materials
used in the device, as well as, improper storage and processing of such equipment.
Segregated household waste collection allows recycling of materials and components of
which the device was made of. In order to get detailed information about recycling of
this particular product, please contact your retailer or a local authority.
Użycie symbolu WEEE (przekreślony kosz) oznacza, że niniejszy produkt nie może być
traktowany jako odpad domowy. Prawidłowa utylizacja zużytego sprzętu pozwala
uniknąć zagrożeń dla zdrowia ludzi i środowiska naturalnego, wynikających z możliwej
obecności w sprzęcie niebezpiecznych substancji, mieszanin oraz części składowych,
a także niewłaściwego składowania i przetwarzania takiego sprzętu. Zbiórka selektywna
pozwala także na odzyskiwanie materiałów i komponentów, z których wyprodukowane
było urządzenie. W celu uzyskania szczegółowych informacji dotyczących recyklingu
niniejszego produktu należy skontaktować się z punktem sprzedaży detalicznej,
w którym dokonano zakupu, lub organem władzy lokalnej.
Manufacturer No/Kod fabryczny: HS-109B
Product No/Numer katalogowy: SR-1003
Batch No/Numer partii: 35/18
www.lanberg.eu
Advertisement
