Related Manuals for Jema Autolifte JA2800S
Summary of Contents for Jema Autolifte JA2800S
- Page 1 JA2800S Movable Scissor Lift Lifting Capacity: 2800 KG INSTALLATION, OPERATION AND MAINTENANCE MANUAL Read this entire manual carefully and completely before installation or operation of the lift.
-
Page 2: Table Of Contents
WE ARE HERE TO SURPRISE! INDEX 1. Important safety instructions………………………………………….…3~5 1.1 Important notices 1.2 Qualified personnel 1.3 Danger notices 1.4 Warning signs 1.5 Sound level 1.6 Training 2. Overview of the lift………………………………………………….……..4~5 2.1 General descriptions 2.2 Technical data 2.3 Construction of the lift 3. -
Page 3: Important Notices
1.1 Important notices Jema Autolifte will offer one-year quality warranty of the lift, during which any quality problem will be properly solved to the user's satisfaction. However, we will not take any responsibility for whatever bad consequence that may result from improper installation and operation, overload running or improper ground conditions. -
Page 4: Warning Signs
WE ARE HERE TO SURPRISE! 1.4 Warning signs 1.5 Sound Level The sound emitted from the lift should not exceed 75DB. For the sake of your health, we suggest that you install a noise detector in your working area. 1.6 Training Only qualified staff, which has been properly trained, can operate the lift. -
Page 5: Technical Data
Lifting height Electrical requirement JA2800S 2800kg 50 Sec 1200mm 220V/240V, Single Phrase Weight of JA2800S = 415 KG. 2.3 Construction of the lift 3. Installation instructions 3.1 Preparations before installation 3.1.1 Tools and equipments needed √ Electrical drill √ Open wrenches √... -
Page 6: Precautions For Installation
WE ARE HERE TO SURPRISE! 3.2 Precautions for installation 3.2.1 Joints of oil hose must be firmly connected in order to avoid leakage. 3.2.2 All bolts should be firmly checked. 3.2.3 Do not place any vehicle on the lift in the case of trial running. 3.3 Installation Step1, Connect the handle on the engine kit. - Page 7 WE ARE HERE TO SURPRISE! Step4, Connect the power and push UP button until the lift goes to about 500mm. Step 5, Mount the lock releasing wire...
- Page 8 WE ARE HERE TO SURPRISE! Step 6, Mount the arms and arm locks.
-
Page 9: Items To Be Checked After Installation
The machine must not lift or lower an automobile if its center of gravity is not positioned midw of the rising platforms Jema Autolifte as well as our dealers will not bear any responsibility for any consequence as a result of operating the lift in unbalance conditions. -
Page 10: Descriptions Of Control Box
WE ARE HERE TO SURPRISE! 4.2 Descriptions of control box 4.3 Operation flow chart Lowering Raising Turn on the power switch Turn on the power switch Press UP button Press UP button Motor drives the gear pump work Press the DOWN button Cylinder piston drives the platform to rise The lift is lowered The lift is raised... - Page 11 WE ARE HERE TO SURPRISE! 4.4 Operation instructions To raise the lift 1. Make sure that you have read and understood the operation manual before operation. 2. Drive and park the vehicle midways on the lift. 3. Place the four rubber pads under the prop-points of the vehicle and ensure that the car’s gravity have fallen on the rubber pads.
- Page 12 5. Trouble Shooting ATTENTION: If the trouble could not be fixed by yourself, please do not hesitate to contact Jema Autolifte for help. Jema Autolifte will offer our service at the earliest possible time. Your troubles will be judged and solved much faster if you could provide us more details or pictures of the trouble.
- Page 13 WE ARE HERE TO SURPRISE! 6. Maintenance Easy and low cost routine maintenance can ensure the lift works normally and safely. The following are requirements for routine maintenance. You may choose the frequency of routine maintenance by consulting your lift’s working conditions and time. The following parts need to be lubricated.
- Page 14 WE ARE HERE TO SURPRISE! 7. ANNEX Annex1, Overall diagram...
- Page 15 WE ARE HERE TO SURPRISE! Annex 2 Hydraulic working system Annex3, Separate diagrams for the lift For the pump: DESCRIPTION Motor Hydraulic block Overflow valve Fitting Cushion valve Absorbing oil hose Oil filter Throttle valve Oil hose tie-in Electrical unloading valve One-way valve Gear pump Oil tank...
- Page 16 WE ARE HERE TO SURPRISE! Annex4, EC Declaration...
- Page 17 WE ARE HERE TO SURPRISE!