Table of Contents
Advertisement
- THE CD IS NOW READY TO BE PLAYED.
- TO REMOVE A DISC, FOLLOW THE SAME PROCEDURE AS DESCRIBED ABOVE,EXCEPT TO REMOVE THE CD
INSTEAD OF INSERTING IT INTO THE COMPARTMENT, BY PLACING ONE FINGER AT THE MIDDLE OF DISC
(CENTER SPINDLE) & THE OTHER AT THE EDGE OF THE DISC & GENTLY PULLING UPWARDS.
- IMPORTANT : ALWAYS HOLD A CD BY ITS EDGES. AVOID GETTING ANY FINGER PRINTS, SMUDGES OR DIRT
ONTO THE SURFACE OF A DISC. IN CASE THIS HAPPENS, USE A SPECIAL CD-CLEANING CLOTH OR CLEANING
KIT TO REMOVE THE DIRT OR SMUDGES.
NORMAL CD OPERATION
IMPORTANT:
MAKE SURE THERE IS NOTHING PLUGGED INTO THE AUX JACK.
- INSERT A CD AS DESCRIBED.
- SLIDE THE FUNCTION SWITCH TO "CD(AUX)".
- THE CD WILL SPIN MOMENTARILY AND THEN THE DISPLAY WILL SHOW THE TOTAL NUMBER OF T RACKS (SONGS) OF
T HE DISC.
- PRESS THE PLAY/PAUSE BUTTON
PLAYING. THE DISPLAY WILL INDICATE THE CURRENT TRACK NO. ("01" IF IT IS THE FIRST TRACK).
- AT ANYTIME DURING PLAYBACK, PRESS THE "PLAY/PAUSE" BUTTON
PRESS PLAY/PAUSE BUTTON TO RESUME OPERATION AT THE SAME TRACK & POSITION.
- AT ANYTIME DURING PLAYBACK, PRESS THE "STOP" BUTTON TO STOP OPERATION OF THE SET. THIS WILL RESET
THE CD-PLAYER TO THE FIRST TRACK (IF YOU PRESS PLAY AFTER STOP, THE FIRST TRACK WILL ALWAYS
START PLAYING).
- AT ANYTIME DURING PLAYBACK, "PRESS AND RELEASE" THE SEEK/SCAN BUTTONS :
BACKWARDS OR FORWARDS BY ONE TRACK, AS DESIRED.
- AT ANYTIME DURING PLAYBACK, "PRESS AND HOLD" THE SEEK/SCAN BUTTONS :
FAST-REVERSE (REVIEW) OR FAST-FORWARD (CUE) THE SPECIFIC TRACK, WHICH IS CURRENTLY PLAYING.
- AT ANYTIME DURING PLAYBACK, PRESS THE "CD REPEAT BUTTON" AS FOLLOWS:
PRESS ONCE = DISPLAY WILL SHOW "REPEAT 1", TO REPEAT THE
CURRENT TRACK
PRESS TWICE = DISPLAY WILL SHOW "REPEAT ALL" ,TO REPEAT
ALL TRACKS (FULL CD)
PROGRAMMING THE CD-PLAYER
- THE CD PLAYER CAN BE PROGRAMMED TO PLAY ANY SEQUENCE OF UP TO 20 TRACKS, AS DESIRED.
- ALWAYS PRESS THE STOP KEY BEFORE STARTING THE PROGRAMMING.
- PRESS THE PROGRAM SWITCH
TO INDICATE THAT THE SET IS NOW IN "MEMORY PROGRAMMING MODE", AT THE FIRST MEMORY POSITION.
- PRESS THE SEEK/SCAN SWITCHES
BE STORED IN THE FIRST MEMORY (PROGRAM) POSITION, AND PRESS
YOUR SELECTION.
- WHEN YOU PRESS
PROG.
- REPEAT THE PREVIOUS 2 STEPS, EACH TIME SELECTING ANY TRACK NUMBER OF YOUR CHOICE TO BE STORED
IN THE SUCCESSIVE MEMORY (PROGRAM) POSITIONS.
- AFTER EACH TRACK NUMBER, REMEMBER TO PRESS THE PROGRAM SWITCH
- AFTER A MAXIMUM OF 20 SONGS (OR LESS) HAVE BEEN SELECTED AS DESCRIBEDABOVE, PRESS THE
SWITCH.
PROG.
- THE DISPLAY WILL NOW SHOW THE EXACT SONG SEQUENCE IN MEMORY BY DISPLAYING ALL THE SONG
NUMBERS RAPIDLY.
- ALSO, THE "PROG"
PROG.
(SEQUENCE).
- PRESSING PLAY
WILL NOW PLAY BACK THE "SAVED SEQUENCE" IN THE PROGRAM MEMORY.
- TO CLEAR (CANCEL) THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY, SIMPLY PRESS "STOP"
TWICE, OR SWITCH "OFF" THE SET.
ALBA User Manual
. THE DISK WILL START SPINNING & THE FIRST SONG (TRACK) WILL START
,THE DISPLAY WILL SHOW "PROG" AND THE "01" WILL FLASH,
PROG.
OR
TO SELECT THE TRACK (SONG) NUMBER YOU WISH TO
NEXT
BACK
THE DISPLAY WILL ADVANCE TO THE NEXT MEMORY POSITION (eg. "02").
WILL REMAIN "ON" TO INDICATE THAT YOU HAVE SAVED APROGRAM-MEMORY
- 5 -
TO PAUSE OPERATION OF THE UNIT.
OR
NEXT
BACK
OR
TO
NEXT
BACK
(PROGRAM) TO CONFIRM
PROG.
.
PROG.
TO SKIP
Advertisement
Table of Contents
