Advertisement
Quick Links
• Visit http://www.corning.com/cablesystems/videos for additional information and videos.
• Visit www.corning.com/cablesystems/safety for full safety precautions.
EDC-02P-NH
1.
CARTON CONTENTS
• environmental Distribution Center (eDC) Housing with no holes
• Hardware Kit containing:
•
(1) Unit identification label
•
(1) Label, 2 x 12 position
•
(2) 8-32 x 0.5 inch phillips-head screws
•
(4) 12-24 x 0.5 inch phillips-head screws
•
(2) 6-32 Locknuts
•
(1) m6 washer
•
(2) U-shaped washers
•
(1) Quick release Latch Kit
2.
TOOLS REQUIRED
• phillips-head screwdriver
• Slotted screwdriver
• 5/16-inch (8 mm) socket or wrench
3.
ADDITIONAL MATERIALS (PURCHASED SEPARATELY)
may or may not be required depending on your application.
• Connector panels (CCH-CpXX-YY)
• (2) Cable entry port Fittings (eDC-2eC-KIt or eDC-2N4-KIt (NemA 4) or eDC-2Wt-KIt)
• mounting hardware appropriate for your installation
• Grounding kit (HDWr-GrND-KIt) for armored cable
• buffer tube Fan-Out kits (FAN-OD25-YY)
• pigtailed panels (CCH-CpXX-YY-p03ZZ)
• pigtailed modules (CCH-rmXX-YY-p03ZZ)
• Splice trays (2r or 4r for eDC-02p, 2S or 4S for others)
STANDARD RECOMMENDED PROCEDURE 003-304 | ISSUE 10 | September 2010 | PAGE 1 OF 7
Central Member Strain-Relief Bracket
Splice Tray Mounting Location
Sheath Retention Bracket
environmental
Distribution Center
(eDC-02p/06p/12p-NH)
p/n 003-304, Issue 10
Radius Control Guides
Fan-out Bracket
Drop Cable Strain-Relief Bracket
TPA-2904
Connector Panel Support Brackets
•
(2 feet) Spiral wrap
•
(4) Cable ties
•
(1) Self-sticking wire clip
•
(2) Self-sticking routing clips
•
(1) Universal Cable Clamp (UCC) kit
•
(1) UCC bracket
•
(1) buffer tube fan-out bracket
• Hole-Saw (2 3/8-inch or 1 3/8-inch)
• tape measure
• Side cutters
Advertisement
Related Manuals for CORNING EDC-02P-NH
Summary of Contents for CORNING EDC-02P-NH
- Page 1 Distribution Center (eDC-02p/06p/12p-NH) p/n 003-304, Issue 10 • Visit http://www.corning.com/cablesystems/videos for additional information and videos. • Visit www.corning.com/cablesystems/safety for full safety precautions. EDC-02P-NH Radius Control Guides Central Member Strain-Relief Bracket Fan-out Bracket Drop Cable Strain-Relief Bracket Splice Tray Mounting Location...
-
Page 2: Housing Preparation
NOTE: If you will be mounting the eDC without the stabilizer bracket, discard it at this time. rotate the top bracket of the eDC-02p-NH (not necessary Stabilizer Bracket on -06p and -12p) so the elliptical hole is exposed. position the housing as desired and secure using ¼-inch screws in the top and bottom... - Page 3 Step 3: Ground armored cable using (1) HDWr-GrND-KIt per cable. 1. Cut a slit into oppsite sides of the outer 3. Position the top plate and lock nut on the sheath and armor about 2 in (5 cm). To do outer sheath over the base plate.
-
Page 4: Cable Routing
• tWO complete loops for eDC-02p-NH • tHree complete loops for eDC-06/12p-NH STANDARD RECOMMENDED PROCEDURE 003-304 | ISSUE 10 | September 2010 | PAGE 4 OF 7... - Page 5 Step 4: mark the buffer tube(s) and pigtail(s) ¾ inch from where they will enter the splice tray (eDC-02p-NH shown). Step 5: Unwind buffer tube(s) and pigtail(s) from the radius guides and bring them as pairs to a convenient splicing location.
- Page 6 9.2. For Buffer Tube Fan-Out Kits EDC-02P-NH EDC-06/12P-NH Step 1: route the buffer tube(s) twice Step 1: remove splice tray holder bracket. around the radius guides in a counterclockwise direction. Step 2: route the buffer tube(s) three times around the radius guides in a counterclockwise direction.
- Page 7 1-800-743-2671 • FAX +1-828-325-5060 • International +1-828-901-5000 • http://www.corning.com/cablesystems Corning Cable Systems reserves the right to improve, enhance, and modify the features and specifications of Corning Cable Systems’ products without prior notification. All trademarks are the properties of their respective owners. Corning Cable Systems is ISO 9001 certified.
Need help?
Do you have a question about the EDC-02P-NH and is the answer not in the manual?
Questions and answers