Advertisement
Table of Contents
Specifications
Environment
Devices
Transmission
Bandwidth
Peripherals' Impedance
Insertion Loss
Common Mode Rejection Ratio
THD
Maximum Input Level
Impedance Transformation Ratio
Cable: Cat 5E UTP/STP
Unbalanced In/ Out Cable
Ground Loop Isolation
Connectors
Pin Configuration
Max. Distance:
Cat 5E/6 UTP/STP
Temperature
Enclosure
Weight
Dimensions
Warranty
Order Information
8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5
Tel: (514) 905-0588
Toll Free (North America): (877) 689-5228
E-mail: videoease@muxlab.com
© MuxLab Inc.
Unbalanced line-level analog audio.
DVD players, audio receivers, audio amplifiers and
audio mixers, audio matrix switchers and other
unbalanced line-level audio equipment.
Transparent to the user
20 Hz to 20 kHz
Source 100 Ω Mx, Receiver 10 kΩ min.
Less than 2 dB per pair over the frequency range
Greater than 60 dB at 1 kHz
Less then 0.007% @ 1 kHz
1.1 Vp-p
Single unit: 4:1 (source: line)
24 AWG or lower solid copper twisted pair wire
Impedance: 100 ohms at 1 MHz
Maximum capacitance: 20 pf/ft
Attenuation: 6.6 dB/1,000 ft at 1 MHz
Shielded, coaxial
Range of +/-50VDC
Four (4) RCA receptacles for audio, one (1) RJ45 jack
Audio 1: Pins 7(R) & 8(T)
Audio 2: Pins 3(R) & 6(T)
Audio 3: Pins 4(R) & 5(T)
Audio 4: Pins 1(R) & 2(T)
3250 ft (1 km)
Operating: 0° to 55°C
Storage: -20° to 85°C
Humidity: Up to 95% non-condensing
Fire retardant plastic
3.6 oz (103 g)
2.40" x 2.25" x 1.00" (6.10 x 5.72 x 2.54 cm)
Lifetime
500033
Quad Audio Balun
Fax: (514) 905-0589
URL: www.muxlab.com
94-000309-D SE-000412-D
Quad Audio Balun
500033
Quick Installation Guide
Overview
The Quad Audio Balun allows up to four (4) analog line audio signals to be transmitted
via an unshielded twisted pair (UTP) cable in a point-to-point connection. Used in pairs,
the Quad Audio Balun eliminates up to four (4) coaxial cables, allowing audio-video
equipment to be connected via a space-efficient and cost-effective Category 5E/6
twisted pair cable and supports Hi-Fi audio signal transmission. The Quad Audio Balun
also works in conjunction with other MuxLab analog audio baluns such as the 500019.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for MuxLab Quad Audio Balun
-
Page 1: Specifications
Overview Ground Loop Isolation Range of +/-50VDC The Quad Audio Balun allows up to four (4) analog line audio signals to be transmitted Connectors Four (4) RCA receptacles for audio, one (1) RJ45 jack via an unshielded twisted pair (UTP) cable in a point-to-point connection. Used in pairs, Pin Configuration Audio 1: Pins 7(R) &... - Page 2 No Audio Open contact Check wiring to ensure continuity. At the audio source end, connect a Quad Audio Balun to the audio output using the Defective Audio Balun Change Audio Baluns for another pair. appropriate number of RCA cables. Check DC loop resistance and verify if distance At the audio receiver end, connect a Quad Audio Balun to the audio input using the spec is exceeded.
Need help?
Do you have a question about the Quad Audio Balun and is the answer not in the manual?
Questions and answers