Summary of Contents for Powerlink CPE
- Page 2 A. Check the parts in your box CPE SET DC 12V/1.5A Power Adapter PoE DC Injector Hose Clamps Manual & QIG CD Paper QIG B. How to fix the CPE on the Pole (1”- 1.5”) (For better water resistance please wrap the RJ45 connector)
-
Page 3: Poe Connection
1. Open the CPE enclosure you will find two RJ45 Jacks two LEDs and one reset button. 2. Connect the PoE cable to either LAN or WAN port. 3. To reset the CPE just press and hold the reset button for about 10 seconds and wait for 55 seconds to reboot the CPE. - Page 4 Configuration The WLAN Broadband Router is delivered with the following factory default parameters on the Ethernet LAN interfaces. Default IP Address: 192.168.1.254 Default IP subnet mask: 255.255.255.0 WEB login User Name: <empty> WEB login Password: <empty> The device has three operation modes (Gateway/Bridge/WISP). The default IP addresses for the device are 192.168.1.254, so you need to make sure the IP address of your PC is in the same subnet as the device, such as 192.168.1.X.
- Page 5 Part II: Internal Web Management CPE AP Model (IP Share Connection) 1、 Install the antenna & power adapter, then connect the LAN cable with LAN port of this equipment. Another side of cable line connects with network card of computer. Waiting for booting around 20 seconds.
- Page 6 1. In Operation Mode, select Bridge and press Next>> 2. In Time Zone Setting, if you don’t need any change, please press Next>> 3. In LAN Interface Setup, you may change the setting for IP address, DHCP and etc. then press Next>>...
- Page 7 4. In WAN Interface Setup, select DHCP Client for your connection of WAN Access Type and press Next>> 5. In Wireless Basic Setting, select AP for your Mode and change your SSID setup, then press Next>> 6. In Wireless Security, select your setup of wireless security (WEP, WPA) and press Finished to reboot around 20 seconds.
- Page 8 Select the TCP/IP Settings from left side of setup frame and choice LAN Interface. Then choosing Disable from DHCP and press Apply Changes to reboot around 20 seconds to complete the setup. Note: Please connect cable line with LAN port when you use this equipment to connect IP Share.
- Page 9 CPE Client Model (Wireless Network Card Connection) Select the Setup Wizard on the left side of setup frame and press Next>>...
- Page 10 1. In Operation Mode, select Bridge and press Next>> 2. In Time Zone Setting, if you don’t need any change, please press Next>> 3. In LAN Interface Setup, you may change the setting of IP address, DHCP and etc. then press Next>>...
- Page 11 4. In WAN Interface Setup, select DHCP Client for your connection of WAN Access Type and press Next>> 5. In Wireless Basic Setting, select Client for your Mode and change your SSID setup, then press Next>> 6. In Wireless Security, select the same AP setup of wireless security (WEP, WPA) which you want to connect and key in password.
- Page 12 Select Wireless from left side of setup frame and press Site Survey Press Refresh to search Access Point SSID Select Access Point SSID and press Connect . If connection is available, the Connect successfully will show on screen. Select the TCP/IP Settings from left side of setup frame and choice LAN Interface. Then choicing Disable from DHCP and press Apply Changes to reboot around 25 seconds to complete the setup.
- Page 13 CPE WDS Model Setup (Bridge Joint) A、 Select Management in left side of setup frame and press Status In Access Point Status, the BSSID of Wireless Configuration shows different WAN MAC Address. For example, the A router show and the B router show 00:0e:4c:d2:ea:c0 Take note of two different BSSID.
- Page 14 1. In Operation Mode, select Bridge and press Next>> 2. In Time Zone Setting, if you don’t need any change, please press Next>> 3. In LAN Interface Setup, you may change the setting of IP address, DHCP and etc. then press Next>>...
- Page 15 4. In WAN Interface Setup, select DHCP Client for your connection of WAN Access Type and press Next>> 5. In Wireless Basic Setting, select WDS for your Mode and change your SSID setup, then press Next>> 6. In Wireless Security, select your setup of wireless security (WEP, WPA) and press Finished to reboot around 25 seconds.
- Page 16 C、 Select the WDS Settings from left side of setup frame. In WDS setting, choice Enable WDS and key in another one BSSID WAN MAC Address without colon. For example, key in the B router’s when you set the A router 000e4cd2eac2 and key in the A router’s when you set the B router.