Specifications; Maintenance - STA-RITE Sunbrite Series Owner's Manual

SPECIFICATIONS

Sunbrite ™ Large Underwater Lights
U.S.
Model
12 Volts -
100 Watts
05501-2204 05501-2232
05501-2205 05501-2233
05501-2206 05501-2234
05501-2207 05501-2235
05501-2208 05501-2236
05501-2209 05501-2237
05501-2210 05501-2238
12 Volts -
200 Watts
05501-2211 05501-2239
05501-2212 05501-2240
05501-2213 05501-2241
05501-2214 05501-2242
05501-2215 05501-2243
05501-2216 05501-2244
05501-2217 05501-2245
120 Volts -
300 Watts
05502-1990 05502-2218
05502-1991 05502-2219
05502-1992 05502-2220
05502-1993 05502-2221
05502-1994 05502-2222
05502-1995 05502-2223
05502-1996 05502-2224
120 Volts -
500 Watts
05502-1997 05502-2225
05502-1998 05502-2226
05502-1999 05502-2227
05502-2200 05502-2228
05502-2201 05502-2229
05502-2202 05502-2230
05502-2203 05502-2231
Canada Cord Length
Model in Feet (m)
15 (4.5)
30 (9.1)
50 (15.2)
75 (22.8)
100 (30.5)
125 (38.1)
150 (45.7)
15 (4.5)
30 (9.1)
50 (15.2)
75 (22.8)
100 (30.5)
125 (38.1)
150 (45.7)
15 (4.5)
30 (9.1)
50 (15.2)
75 (22.8)
100 (30.5)
125 (38.1)
150 (45.7)
15 (4.5)
30 (9.1)
50 (15.2)
75 (22.8)
100 (30.5)
125 (38.1)
150 (45.7)

MAINTENANCE

Electrical shock hazard. Before removing
fixture from pool wall, ALWAYS TURN OFF THE POWER
at the breaker. Installation and maintenance of this cir-
cuit, the light, light niche, and any other accessories
attached to this circuit must be performed by a licensed
electrician. The complete electrical system must be
installed, tested, and approved by a licensed electrician
before it is placed in operation.
Risk of cuts, burns, and electrical shock.
Avoid direct impacts on glass lens. Do not install dam-
aged or broken lens.
For Sunbrite Lamps
™
See Figure 2, Page 5, for Key numbers.
1. Be sure that the power is off. Allow the lamp to cool
before re-lamping.
2. Loosen the captive leader screw (Key No. 1) from the
top of the fixture face ring (Key No. 2)
NOTICE: The screw in the face ring may be recessed.
3. Remove the lamp housing (Key No. 6) and place on
the pool deck.
4. Using a clean soft lint free cloth, carefully wipe all
sealing surfaces on the lamp housing and lens.
Replace lamp with an equivalent to the original lamp.
5. Replace the gasket (Key No. 4).
6. To reassemble the lens assembly to the lamp housing,
reverse the disassembly process. Be sure that the lamp
housing is clean, dry, and free of all traces of mois-
ture, before sealing the fixture.
7. Wind the extra cord around the lamp housing and
place the lamp housing back in the niche. Be sure to
align the locator tab at the bottom of the lamp hous-
ing with the notch in the bottom of the niche.
8. Fasten the lamp housing into the niche using the cap-
tive leader screw (Key No. 1) at the top of the trim
ring.
4