Summary of Contents for Bristan DOC M Series
- Page 1 Installation Overview DOC M Packs Models covered: DOCM-T3 B, DOCM-T3 W Please keep this booklet for future reference. Installer, when you have read these instructions please ensure you leave them with the user.
-
Page 2: Table Of Contents
Contents Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have designed this product with your enjoyment and safety in mind. To ensure that it works to its full potential, it needs to be fitted correctly. These fitting instructions have been created to give you all of the information you need and, if you need any further help, please do not hesitate to contact us using the number at the bottom of this page. -
Page 3: Important Safety Information
Important Safety Information • Please read these instructions thoroughly and retain for future use. • All products manufactured and supplied by Bristan are safe provided they are correctly installed, used and receive regular maintenance in accordance with these instructions. •... -
Page 4: General Guidelines
General Guidelines This product has been tested to the Water Regulations Advisory Scheme (WRAS) and satisfies the requirements of the Water Supply (Water Fittings) Regulations 1999 and current bylaws. For full Installation Requirements & Notes (IRN) please visit www.wras.co.uk/directory. Designed to comply with BS EN 200 for combination taps to be used within systems designed to BS 6700. -
Page 5: Installation Plan
Installation Plan Standard DOC M Pack Note: Please adhere to all standard height measurements shown in the following diagram. Min 600 Max 700 82.5 Min 140 Max 160 Hinged Support Rail Pull Rail Fixed To Door Min 2200 Dimensions are nominal and in millimetres. Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. -
Page 6: Installation
Installation - WC Pan Insert fixing bolts through the holes in the Position the cistern on its back. Assemble cistern, using the rubber and large metal and insert the flush mechansim. washer. Place the large rubber gasket into the Lift the cistern onto the pan so the flush entrance of the pan. - Page 7 Installation - WC Pan Fit the washers and wing nuts to the Insert a pan connector into the waste underside of the cistern and tighten the pipe. nuts. Ensure the cistern is level by placing spirit Draw a line around the base of the pan to level along the back against the wall.
- Page 8 Installation - WC Pan Return the pan to the desired location, make the plumbing connections and Drill fixing holes for cisten/pan through ensure that they are water tight. Ensure the marks on the wall/floor. Use wall the pipework is flushed prior to plugs according to wall/ floor surface.
- Page 9 Installation - WC Pan Close/Off Open/On position position Fit the lever and place the lid onto the Connect the cold water supply. Turn on cistern, use cistern blanking plug to cover water supply at the isolation valve and unuse hole. check for leaks.
-
Page 10: Basin
Installation - Basin • Consider and plan the design and accomodation of your DOC-M suite around the layout of your waste system and suitablity of future access. • Use suitable wall fixings for your wall construction. • Do not overtighten wall fixings, taps or wastes onto ceramic surfaces. •... -
Page 11: Solo T3 Tap
Installation - Solo T3 Tap Position the fixing base into the hole in the basin ensuring the rubber washer is fitted Screw the fixing rods into the bottom of between the fixing base and the basin. the fixing base. Screw the copper connecting pipes into the Slide the metal plate onto the threaded bottom of the fixing base by hand only (DO rods under the basin and secure the fixing... -
Page 12: Operation
Installation - Solo T3 Tap Turn on both water supplies, Push the mixer body onto the fixing base operate the handle in both hot and cold ensuring the rubber ‘O’ ring is fitted into positions, letting the water flow for a few the grove in the bottom of the mixer body. -
Page 13: Grab Rails
If installing a metallic rail in a bath/shower area the rail may need to be earthed (IEE wiring regulations); not all rails are suitable for use in a wet area. Ensure the wall and fixings being used are suitable. Bristan are unable to specify fixings due to the number of fixing/wall type combinations. -
Page 14: General Maintenance
Clean the surfaces of the rails with hot soapy water and a cloth. Note: For any other maintenance information, consult the individual instructions with each product or contact Bristan on the number at the bottom of this page, Guarantee At Bristan, we want to make things as easy as possible for our customers. -
Page 15: Notes
Notes Please use this space to add any notes you or your installer may have regarding the pumbing system / installation of this product. Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. - Page 16 DOCM-T3 Part Numbers: Issue: D2 Useful contact details: Customer Service: 0844 7016273 Bristan Group Ltd. Customer Service Email: Birch Coppice Business Park Customercare@bristan.com Dordon Tamworth Customer Service Fax: Staffordshire 0844 7016275 B78 1SG Reception: Web: http://www.bristan.com 0844 7016274 Email: enquire@bristan.com Join us on...
Need help?
Do you have a question about the DOC M Series and is the answer not in the manual?
Questions and answers