Fisher Engineering HD2 Installation Instructions Manual

Snowplows

Advertisement

Fisher Engineering
50 Gordon Drive, Rockland, Maine 04841‑2139 • www.fisherplows.com
HD2™ and HDX™ Snowplows
Installation Instructions
Read this document before installing the
snowplow.
See your FISHER
vehicle application recommendations before
installation. The eMatch tool has specific
vehicle and snowplow requirements.
90750, 90800, 90850, 90900, 93800,
93900, 97200, 97200‑1, 97250(CH)
CAUTION
CAUTION
outlet/website for specific
®
A DIVISION OF FISHER, LLC
97250‑1(CH), 97300, 97300‑1
Lit. No. 41775, Rev. 02
August 15, 2017

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HD2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Fisher Engineering HD2

  • Page 1 93900, 97200, 97200‑1, 97250(CH) 97250‑1(CH), 97300, 97300‑1 Fisher Engineering August 15, 2017 50 Gordon Drive, Rockland, Maine 04841‑2139 • www.fisherplows.com Lit. No. 41775, Rev. 02 HD2™ and HDX™ Snowplows Installation Instructions CAUTION Read this document before installing the snowplow. CAUTION...
  • Page 2 90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 Lit. No. 41775, Rev. 02 August 15, 2017...
  • Page 3: Safety Definitions

    90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 SAFETY DEFINITIONS WARNING/CAUTION AND INSTRUCTION LABELS WARNING Become familiar with and inform users about the Indicates a potentially hazardous situation warning labels on the back of the blade and the that, if not avoided, could result in death or instruction label on the headgear.
  • Page 4: Safety Precautions

    90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 SAFETY PRECAUTIONS HYDRAULIC SAFETY Improper installation and operation could cause WARNING personal injury and/or equipment and property damage. Hydraulic fluid under pressure can cause skin Read and understand labels and the Owner's Manual injection injury.
  • Page 5: Cell Phones

    90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 FIRE AND EXPLOSION NOISE Airborne noise emission during use is below 70 dB(A) WARNING for the snowplow operator. Gasoline is highly flammable and gasoline vapor is explosive. Never smoke while VIBRATION working on vehicle.
  • Page 6 90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 HEADGEAR AND A‑FRAME 5. Inspect the step pins attaching the A‑frame to the headgear to see whether they are secured with temporary shipping wires or cotter pins. If the NOTE: For easier assembly and installation, step pins are secured with shipping wires, vehicle and all snowplow components should...
  • Page 7 5. Align the angle ram rods with the angle ram Secure with a 1" locknut and tighten as much as holes on the blade (HD2™ blades) or quadrant (HDX™ blades) and attach them using two possible while allowing the A‑frame to pivot.
  • Page 8 90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 HEADLAMPS Cable Ties WARNING Your vehicle must be equipped with snowplow headlamps and directional lights. Cable Headlamps, hardware and instructions are found in Ties the headlamp box. 1. Attach the headlamps to the hole and slot in the headgear light bracket by following the instructions included with the headlamps.
  • Page 9: Hydraulic Unit

    Activate the control FLOAT function and manually collapse the The HDX™ and HD2™ snowplow hydraulic system lift ram all the way. Turn the control OFF. comes from the factory pre‑assembled, partially filled and fully tested.
  • Page 10 90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 HDX™ BLADE ATTACK ANGLE 2. Align the desired attack angle holes in the quadrant and blade. ADJUSTMENT The HDX blade features a bolted connection between 65° the quadrant and main blade that allows adjustment among three attack angles—55°, 65°...
  • Page 11 90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 A special spring replacement tool (PN 20043‑1) 4. Torque the upper and lower fasteners as shown. must be used to safely make this adjustment. NEVER ATTEMPT SPRING REMOVAL Torque 3/4"...
  • Page 12: Final Adjustments

    1/4" x 1‑1/2" cotter pins. With the snowplow attached to a properly ballasted vehicle and the blade lowered to the ground, the HD2™ Snowplow A‑frame should be parallel with the ground. Three attachment holes are provided to allow the A‑frame Mount Height (in) A‑Frame Hole...
  • Page 13 90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 Stacking Stops – HDX™ Snowplow • When using the 55° blade attack angle in the top and middle positions, install the stacking stops to the cross channel of the headgear using four Stacking stops are required for all installations using 3/8"...
  • Page 14 90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 Adjusting Lift Chain Reattach the loose end of the lift chain to the passenger's side of the A‑frame with the retained U‑bolt and locknuts, being sure to maintain any WARNING length adjustment made in Step 2.
  • Page 15 HD2™ and HDX™ snowplows come with the lift chain Grease the pivot beam at the beginning of the spring connecting link ("quick link") factory installed in snowplow season.
  • Page 16 90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 VEHICLE LIGHTING CHECK Isolation Module installed. Due to the variations in the OEM DRL systems and the different Isolation Module options available, checking 1. Verify the operation of all vehicle front lighting the functionality of the snowplow DRLs will prior to connecting the snowplow harnesses.
  • Page 17 90750, 90800, 90850, 90900, 93800, 93900, 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 OWNER'S MANUAL PACKET D. Control Power Indicator Light The snowplow plugs do need to be connected If the completed snowplow will be delivered to the vehicle harness connectors. immediately, the Owner's Manual should be reviewed with and given to the purchaser according to the The control power indicator light should light...
  • Page 18 97200, 97200‑1, 97250(CH), 97250‑1(CH), 97300, 97300‑1 Fisher Engineering reserves the right under its product improvement policy to change construction or design details and furnish equipment when so altered without reference to illustrations or specifications used. Fisher Engineering or the vehicle manufacturer may require or recommend optional equipment for snow removal.

Table of Contents