Table of Contents
Advertisement
Quick Links
POWERED ELECTRONIC LOCK
FINGERPRINT SCANNER
99.690
GENERAL WARNINGS
Mottura Serrature di Sicurezza S.p.A. thanks you for choosing this product and reminds you to:
- Read these instructions very carefully before installing and using this product and before doing any maintenance.
- Keep these instructions for future use and attach the sales receipt to validate the warranty.
- In case of problems, contact your authorized dealer only.
DO NOT use a liquid, spray, or wet cloth to clean the escutcheon! If liquids enter the scanner, they will oxidize and perma-
nently damage its components. Use a dry cloth only.
DO NOT paint the escutcheon with any method or substance. Failure to follow these instructions will immediately void
the warranty.
Mottura Serrature di Sicurezza S.p.A. reserves the right to modify the characteristics of the products described in these
instructions at any time and without notice. The fingerprint scanner must be powered ONLY with a direct current (DC) line
adapter with voltage from 8 to 24 V and current not below 350 mA (for example, Mottura adapter 99.683). Be very careful
to respect polarity.
DO NOT power the scanner in alternating current (AC): doing so will permanently damage it.
These power instructions refer ONLY to the fingerprint scanner, NOT to the lock, which has its own installation manual.
Battery power is not advisable: the batteries would drain very quickly.
After powering the scanner for the first time, or after a blackout, you have to wait at least 10 minutes for the sensor to heat,
otherwise the scans may be incorrect.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Mottura X Mode 99.690
Summary of Contents for Mottura X Mode 99.690
- Page 1 The fingerprint scanner must be powered ONLY with a direct current (DC) line adapter with voltage from 8 to 24 V and current not below 350 mA (for example, Mottura adapter 99.683). Be very careful to respect polarity.
- Page 2 CONTENTS INSTALLER ESCUTCHEON ........................pag. 3 ASSEMBLY AND ELECTRICAL CONNECTION ..............USER CHANGING THE PIN CODE ON THE INFRARED REMOTE CONTROL ......5 MASTER FINGERPRINTS ......................5 RECORDING MASTER FINGERPRINTS ..................6 RECORDING SERVICE FINGERPRINTS ..................6 IDENTIFICATION AND OPENING OF THE LOCK ..............DELETING ALL FINGERPRINTS, FACTORY RESET ...............
- Page 3 I N S T A L L E R 1. ESCUTCHEON GREEN / RED LED (FUNCTIONS SIGNAL) BRUSHED STEEL ESCUTCHEON BLUE LED (POWER STATUS) SWIPE-TYPE FINGERPRINT SCANNER WITH SENSOR SELF-CLEANING DEVICE 2. ASSEMBLY AND ELECTRICAL CONNECTION Make a 50 x 38 mm opening in the door panel as shown in the figure. Connect the scanner to the door opener logic unit.
- Page 4 I N S T A L L E R Connect the fingerprint scanner to the lock and to the line adapter. The connections must be made by a qualified technician in conformity to current electrical safety standards and to Rules of Good Engineering. N.B.
- Page 5 I N S T A L L E R Switch on power to the scanner and to the XMODE lock, and check that the blue LED located in the inside niche of the scanner is on. U S E R 3.
- Page 6 U S E R 5. RECORDING MASTER FINGERPRINTS Swipe Repeat Repeat Only finger on step 1 after step 1 after green LED scanner green 3 seconds green 3 seconds stays on green LEDs go off LEDs go off briefly LEDs go off; MASTER and then and then...
- Page 7 U S E R 7. IDENTIFICATION AND OPENING OF THE LOCK When the service finger is swiped, the green LED lights and the lock opens. If not (finger not recognized, finger dirty, or poor quality scan), the red LED will light briefly. 8.
- Page 8 www.mottura.it...
Need help?
Do you have a question about the X Mode 99.690 and is the answer not in the manual?
Questions and answers